Qingsong Yan

Qingsong Yan


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 August 2019 in Materials
Verified
Journal Article
Open access
PDF file
PHPengpeng Huang
Pengpeng Huang
GLGang Lu
Gang Lu
QYQingsong Yan
Qingsong Yan
PMPu Mao
Pu Mao
In order to improve the performance of the investment casting shell, ceramic and nylon fiber was added to the silica sol slurry to study the effect of ceramic and nylon fiber on the liquidity of the silica sol slurry and the bending strength of the investment casting shell. Meanwhile, the fracture surface of shell sample was observed by SEM. The experiment results indicate that the movement viscosity of slurry increases with ceramic and nylon fiber content, increasing from 0 to 0.75 wt.%. The movement viscosity of ceramic fiber composite slurry is higher than nylon fiber composite slurry. The wet and high strength of shell firstly increases then decreases, with an increase of ceramic and nylon fiber content. When the ceramic and nylon fibers’ contents are 0.6 wt.%, the maximum wet strengths are 3.56 MPa and 3.84 Mpa respectively, increasing by approximately 38% and 43%. Moreover, the high strength of shell achieves its highest value, 5.08 Mpa, when the ceramic fiber content is 0.6 wt.%; however, when the nylon fiber content was more than 0.3%, the high strength of the nylon fiber reinforced shell was decreased sharply. Therefore, an addition of ceramic and nylon fiber to silica sol slurry distinctly influences the wet and high strength of investment casting shell.

1 November 2018 in China Foundry
Verified
Journal Article
Open access
PDF file
QYQingsong Yan
Qingsong Yan
GLGang Lu
Gang Lu
GLGui-Ming Luo
Gui-Ming Luo
BXBo-Wen Xiong
Bo-Wen Xiong
QZQiang-Qiang Zheng
Qiang-Qiang Zheng
The effect of synergistic action of ultrasonic vibration and solidification pressure on tensile properties of vacuum counter-pressure casting ZL114A alloys was studied systemically through testing and analyzing the tensile strength and elongation subjected to different ultrasonic powers and solidification pressures. The results indicate that the synergistic action of ultrasonic vibration and solidification pressure can result in the refinement of grains and improvement of tensile properties. Both the highest tensile strength and elongation of aluminum alloy were obtained under synergistic action of 600 W ultrasonic power and 350 kPa solidification pressure. Moreover, the tensile fracture morphology shows obvious ductile fracture characteristics. When the solidification pressure is lower than 300 kPa, the effect of ultrasonic power on tensile strength and elongation is more obvious, but when the solidification pressure is higher than 300 kPa, the effect of solidification pressure on tensile strength and elongation is greater. Meanwhile, the size and morphology of the eutectic silicon were improved significantly by the ultrasonic vibration and pressurized solidification. The strip and massive eutectic silicon phase are completely converted into small short rod-like and evenly distributed Si phases at the grain boundary of primary α-Al.

3 June 2015 in Materials Research Innovations
Verified
Journal Article
Closed access
QYQingsong Yan
Qingsong Yan
RWRong Wei
Rong Wei
GLGang Lu
Gang Lu
BLBai-Ping Lu
Bai-Ping Lu
The carbon fibres were used to enhance the materials by selected laser sintering. Gas phase oxidation, dense nitric acid and the coupling reagent processing together with dense nitric acid were adopted to modify carbon fibres, the microstructure of carbon fibres surface after treatment were analysed by SEM, and the strength of the composites was tested. The results demonstrate that the carbon fibre modified by 65–68% KHNO3 + 1% KH550 is considered as the optimal method. With the increase of carbon fibres content, the strength of the composite increases first and then decreases within a certain range. When the carbon fibres content at 3 wt-%, the green strength and the post-curing strength reached 0·87 and 9·614 MPa respectively, and the rate increased by 55·21 and 32·17% compared to the unreinforced.

1 March 2016 in China Foundry
Verified
Journal Article
Open access
PDF file
QYQingsong Yan
Qingsong Yan
HYHuan Yu
Huan Yu
GLGang Lu
Gang Lu
BXBo-Wen Xiong
Bo-Wen Xiong
SXSuai Xu
Suai Xu
The density of vacuum counter-pressure cast aluminum alloy samples under grade-pressuring condition was studied. The effect of grade pressure difference and time on the density of aluminum alloys was discussed, and the solidification feeding model under grade-pressuring condition was established. The results indicate the grade-pressured solidification feeding ability of vacuum counter-pressure casting mainly depends on grade pressure difference and time. With the increase of grade pressure difference, the density of all the aluminum alloy samples increases, and the trend of change in density from the pouring gate to the top location is first decreasing gradually and then increasing. In addition, in obtaining the maximum density, the optimal grade-pressuring time is different for samples with different wall thicknesses, and the solidification time when the solid volume fraction of aluminum alloy reaches about 0.65 appears to be the optimal beginning time for grade-pressuring.

21 February 2018 in DEStech Transactions on Computer Science and Engineering
Verified
Journal Article
Open access
PDF file
QYQingsong Yan
Qingsong Yan
GLGang Lu
Gang Lu
Composite fibers were used to enhance silica sol shell for investment casting. The fracture morphology of the shell was observed and analyzed by scanning electron microscopy (SEM). The influence of the characteristics of the composite fiber on the cast-type shell was analyzed. The results for the high performance of investment casting shell preparation to provide a scientific basis and theoretical support.

13 October 2026 in Coatings
Verified
Journal Article
Open access
PDF file
YLYong Liu
Yong Liu
JXJing Xu
Jing Xu
QYQingsong Yan
Qingsong Yan
JXJing Xu
Jing Xu
QHQiang Hu
Qiang Hu
HZHao Zhang
Hao Zhang
Understanding the distinct roles of representative alloying elements, including rare-earth (RE) solutes such as Gd and Y and non-rare-earth (non-RE) solutes such as Al and Zn, in regulating microstructural evolution and mechanical response is essential for developing high-strength Mg sheets. In this study, Gd and Y are typical RE solutes, whereas Al and Zn are common non-RE alloying elements, and were individually added to pure Mg at an identical concentration of 0.3 at.% to enable a controlled comparison of their effects on microstructural evolution and mechanical response during hot rolling and subsequent annealing. The effects of alloying elements on hot-rolling behavior were first investigated. Mg-Al and Mg-Zn exhibited improved hot rollability, whereas Mg-Gd and Mg-Y showed higher edge-cracking susceptibility after 90% hot rolling. The hot-rolled (HR) Mg-Gd and Mg-Y sheets achieved yield strength (YS) values of 235.5 and 226.4 MPa, respectively, exceeding those of Mg-Al (170.0 MPa) and Mg-Zn (162.8 MPa). Combined microstructural characterizations and DFT calculations revealed that RE solutes strongly segregated at grain boundaries, inducing solute drag, suppressing dynamic recrystallization (DRX), and promoting dislocation accumulation. During subsequent annealing, the grain size increased by only ~1.5 times in Mg-Gd/Mg-Y, whereas increases of 2.6–2.96 times were observed in pure Mg and Mg-Al/Mg-Zn alloys. The RE-containing alloys retained a UTS of ~190 MPa and elongations above 12% after annealing at 500 °C for 240 min. The identical atomic fraction design (0.3 at.%) enabled a direct comparison of the element-specific effects of different alloying elements, providing insights into alloy design and thermomechanical processing strategies for high-performance Mg sheets.