Light detection and ranging (LiDAR) is a type of essential tool for urban planning and geoinformation extraction. Airborne streak tube imaging LiDAR (ASTIL) is a new system with great advantages in the rapid collection of remote sensing data. To the best of our knowledge, a new method to extract a building roof from the echo images of ASTIL is proposed. We improve YOLOv5s with a one-shot aggregation (OSA) module to improve efficiency. The experimental results show that the mean average precision of the OSA-YOLOv5s algorithm can reach 95.2%, and the frames per second can reach 11.74 using a CPU and 39.39 using a GPU. The method proposed can extract building objects efficiently from the echo images of ASTIL and acquire the building roof point cloud.
In this paper, a ground target extraction system for a novel LiDAR, airborne streak tube imaging LiDAR (ASTIL), is proposed. This system depends on only a single echo and a single data source, and can achieve fast ground target extraction. This system consists of two modules: Autofocus SSD (Single Shot MultiBox Detector) and post-processing. The Autofocus SSD proposed in this paper is used for object detection in the ASTIL echo signal, and its prediction speed exceeds that of the original SSD by a factor of three. In the post-processing module, we describe in detail how the echoes are processed into point clouds. The system was tested on a test set, and it can be seen from a visual perspective that satisfactory results were obtained for the extraction of buildings and trees. The system mAPIoU=0.5 is 0.812, and the FPS is greater than 34. The results prove that this ASTIL processing system can achieve fast ground target extraction based on a single echo and a single data source.
ZnO nanorods with mean diameter 200 nm on different substrates were fabricated by hydrothermal method. Fluorescent properties of fabricated ZnO nanorods were researched by both linear and nonlinear excitation using femtosecond lasers. The damage threshold of productions on Si substrate irradiated under intense femtosecond pulses was found much higher than that on Zn plate. Raman spectrum was also applied to investigate relative optical properties. The A1L optical mode was found to be important to the fluorescent properties of ZnO materials.
This paper describes a high-pulse-energy frequency-doubled ultraviolet dye laser operating at a repetition rate of 500 Hz. The pump source is a laser-diode side-pumped Q-switched Nd:YAG laser with a pulse energy of 29 mJ at 532 nm. A master oscillator power amplifier is employed to amplify the output pulse of the dye laser to 8.1 mJ at 566 nm, and by frequency doubling with BBO crystal a pulse energy of 1.7 mJ at 283 nm is achieved with a pulse width of 8 ns. This is more than four times the largest reported pulse energies generated by other fixed-frequency dye lasers when operating at repetition rates of more than 1 kHz. The conversion efficiency and stability of dye laser are discussed, which show the potential for high-speed laser diagnostics in the fields of combustion and turbulent flow detection.
Airborne streak tube imaging LiDAR (ASTIL) enables high-frame-rate 3D imaging but suffers from real-time processing bottlenecks due to massive data throughput and costly full decompression. We propose a compressed-domain detection framework that directly processes natively group-sparse (GS) encoded streak images. The pipeline integrates three components: (1) flag-grid-guided selective decoding for zero-overhead signal extraction; (2) an O(N) Two-Pass Connected Component Labeling (CCL) algorithm replacing DBSCAN; and (3) a 6724-parameter Sparse Set Attention Network (SSAN). Crucially, the SSAN synergizes a 22-D physically grounded feature vector with a dual-prototype cross-attention mechanism, implicitly decoding the bimodal scattering signatures of ASTIL targets. Evaluated on 17,528 airborne frames, our method achieves a Pareto-optimal trade-off, attaining 73.3% Grouped F1-score (G-F1), a diagnostic metric that merges same-class fragments before matching, at 1536 FPS on a single CPU core. This represents a transformative speedup—≈230× faster than PointNet++ and ≈120× faster than Faster R-CNN—while maintaining competitive fidelity. Ultimately, this work demonstrates that aligning algorithmic design with the intrinsic physics of sparse modalities effectively bridges the accuracy-throughput chasm for next-generation real-time airborne remote sensing.