We use a Wiener deconvolution filter to deblur the streak image of streak tube imaging lidar to improve the spatial resolution of the system and reduce the edge blurring effect in point clouds. Experiments were performed to investigate the performance of the deconvolution method. Results show that the spatial resolution improved from 9 to 4.5 mm, and the root-mean-square errors of the edge regions are effectively reduced. Additionally, the transition section decreases from 14 to 5.6 mm when the target is 5 m away from the receiver.
A passively Q-switched sub-nanosecond master oscillator power amplifier (MOPA) laser system at 1064 nm has been reported in this paper. The master oscillator was a passively Q-switched YAG/Nd:YAG/Cr4+:YAG microchip laser, yielding a pulse energy of 0.14 mJ and a pulse width of ∼490 ps at repetition rates of 500 Hz and 1 kHz. After passing a double-pass side-pumped Nd:YAG amplification system, the pulse energy reached 7.6 mJ and 1.7 mJ at 500 Hz and 1 kHz, respectively. The spatial beam deformation caused by the thermally induced birefringence was investigated numerically and experimentally.
A 5 kHz sub-nanosecond master oscillator power amplifier (MOPA) laser system was reported in this paper. The master oscillator was an electro-optically Q-switched Nd:YVO4 laser directly pumped at 879 nm, yielding a pulse energy of 520 µJ and a pulse width of 900 ps at 5 kHz. With two Nd:YVO4 amplifiers directly pumped at 914 nm, the pulse energy was further scaled up. Under the absorbed pump energy of 11.0 mJ, the pulse energy was amplified to 4.2 mJ, corresponding to a peak power of 4.7 MW. The optical-to-optical efficiency of the amplifiers reached 33.5%.
Light detection and ranging (LiDAR) is a type of essential tool for urban planning and geoinformation extraction. Airborne streak tube imaging LiDAR (ASTIL) is a new system with great advantages in the rapid collection of remote sensing data. To the best of our knowledge, a new method to extract a building roof from the echo images of ASTIL is proposed. We improve YOLOv5s with a one-shot aggregation (OSA) module to improve efficiency. The experimental results show that the mean average precision of the OSA-YOLOv5s algorithm can reach 95.2%, and the frames per second can reach 11.74 using a CPU and 39.39 using a GPU. The method proposed can extract building objects efficiently from the echo images of ASTIL and acquire the building roof point cloud.
Airborne streak tube imaging LiDAR (STIL) consists of several different data-generating subsystems and introduces system errors each time it is installed on an aircraft. These errors change with each installation, which makes the parametric calibration of the LiDAR meaningless. In this study, we propose a high-precision reconstruction method for point clouds that can be used without calibrating the system parameters. In essence, after each remote sensing measurement, a self-checking process is performed with experimental data to replace the fixed system parameters. In this process, the splicing error of the same region measured under different conditions is used as a criterion to optimize the reconstruction parameters via a particle swarm optimization (PSO) algorithm. For a detection distance of 3000 m, the elevation error of the point cloud reconstruction reaches more than 1 m if the placement parameters are not optimized; after optimization, the elevation error can be controlled within 0.3 m.
Owing to the special working systems of streak tube imaging lidar (STIL), the time and space dimensions are coupled together on the streak images. This coupling can cause measurement errors in 3D point clouds and can make measurement results more complicated to calibrate than other kinds of lidars. This paper presents a method to generate a time calibration array and an angle calibration array to separate the offset of the streak into time dimension and space dimension. The time and space information of the signal at any position on the streak image can be indexed through these two arrays. A validation experiment on aircraft was carried out, and the range error of the 3D point cloud was improved from 0.41 m to 0.27 m using the proposed calibration method. Thus, using the proposed calibration method can improve the accuracy of the point cloud produced by STIL.