The catalytic properties of complex perovskite-type gadolinium and strontium oxides in carbon dioxide reforming of methane and the production of gaseous olefins by carbon monoxide hydrogenation have been studied. Samples of Gd2SrFe2O7 and Gd2–xSr1+xFe2O7 (х = 0.1; 0.2; 0.3; and 0.4) have been obtained by the sol–gel method and ceramic technology, and have been characterized by means of X-ray diffraction, scanning electron microscopy, photon correlation spectroscopy, Mössbauer spectroscopy, and N2 adsorption–desorption analysis. It has been shown that the sol–gel method allows us to produce samples with better catalytic characteristics than ceramic systems. The nonisovalent substitution of Gd3+ for Sr2+ distorts the structure of complex oxide, resulting in the emergence of the heterovalent state of iron atoms (Fe3+ and Fe4+) reflected in the values of reactant conversion and selectivity for the target products. A sample of Gd2–xSr1+xFe2O7 with х = 0.3 displays the highest catalytic activity in dry reforming of methane reforming, along with the highest selectivity for unsaturated hydrocarbons (ethylene and propylene) in hydrogenation of carbon monoxide.
KCoMoS2 was supported on various carbon support materials to study the support effect on synthesis gas conversion. Next to two activated carbons with high micropore volume, a traditional alumina (γ-Al2O3) support and its carbon coated form (CCA) were studied for comparison. Coating alumina with carbon increases the selectivity to alcohols, but the AC-supported catalysts show even higher alcohol selectivities and yields, especially at higher temperatures where the conversions over the AC-supported catalysts increase more than those over the γ-Al2O3-based catalysts. Increasing acidity leads to decreased CO conversion yield of alcohols. The two activated-carbon-supported catalysts give the highest yield of ethanol at the highest conversion studied, which seems to be due to increased KCoMoS2 stacking and possibly to the presence of micropores and low amount of mesopores.
Ethanol has become a viable feedstock for basic organic synthesis. The catalytic conversion of ethanol provides access to such chemicals as diethyl ether, ethyl acetate, and acetaldehyde. Carbonaceous materials are extensively studied as supports for heterogeneous catalysts due to their chemical and thermal stability, high surface area, and tunable texture. In this paper, ethanol conversion over K10Co3.7Mo12S-catalysts supported on novel activated carbon (AC) materials (i.e., novel powder-AC (DAS and YPK-1), fiber non-woven AC material (AHM), and fabric active sorption (TCA)) was investigated. The catalysts were prepared by the incipient wetness co-impregnation method followed by sulfidation. The catalysts were characterized by employing N2 adsorption–desorption measurements, TEM, SEM/EDX, UV–Vis spectroscopy, and XRF. Catalytic performance was assessed in a fixed-bed down-flow reactor operating at 320 °C, 2.5 MPa, and with continuous ethanol feeding in an He atmosphere. Activity is highly dependent on the support type and catalyst’s textural properties. The activity of the fiber-supported catalysts was found to be greater than the powder-supported catalysts. Ethanol conversion at T = 320 °C, P = 2.5 MPa, and GHSV = 760 L h−1 kgcat−1 increased as follows: (38.7%) KCoMoS2/YPK-1 < (49.5%) KCoMoS2/DAS < (58.2%) KCoMoS2/TCA < (67.1%) KCoMoS2/AHM. Catalysts supported by powder-AC enhanced the formation of MoS2-crystallites, whereas the high acidity of fiber-AC seemed to inhibit the formation of MoS2-crystallites. Simultaneously, a high surface area and a microporous catalytic structure enhance the formation of oxygenates from hydrocarbons. The dehydration and dehydrogenation reactions, which led to the creation of ethene and acetaldehyde, were shown to require a highly acidic catalyst, while the synthesis of ethyl acetate and higher alcohols required a less acidic catalyst.
29 August 2022 in Chemical Engineering Communications
The comparative study of the catalytic behavior of K-modified CoMoS2-catalysts supported on Al2O3, carbon covered alumina (CCA) and graphene coated alumina (GCA containing 0.4, 1.2, and 1.7% of graphene) in synthesis gas and ethanol conversion (separately) to higher alcohols (HAS) and other oxygenates has been carried out. The supports and catalysts were characterized by N2 adsorption-desorption isotherms, pyridine adsorption, SEM, EDX, and TEM. In HAS from syngas, the catalyst supported on GCA materials showed better catalytic performances than the catalysts supported on alumina and carbon coated alumina (Cat-GCA > Cat-CCA > Cat-Al2O3). The spectroscopic results have established that the homogenous uniform coating of alumina by graphene nanosheets follows the order: GCA1 (1.7%) > GCA2 (1.2%) > GCA3 (0.4%). The yield of ethanol has a positive correlation with graphene wt. % in GCA. In ethanol conversion, graphene attenuate the interaction of the support/active site KCoMoS2 and with it its selectivity toward dehydrogenation/condensation reactions. The GCA1 supported catalyst exhibits low activity for the water–gas shift (WGS) reaction compared to its counterpart. Explanations of the observed phenomena have been suggested.
8 April 2021 in International Journal of Green Energy
The main purpose of this present work is to produce and improve Jatropha curcas L biodiesel using mixed natural zeolite and furfural to meet the demand of green and clean production. Trans-esterification of Jatropha oil using natural microporous zeolite (96.6% Thomsonite and 3.4% Analacime) has been carried out. The optimum molar ratio (oil: methanol: zeolite) to yield 85.65 wt.% of Jatropha biodiesel was found to be (1:3:0.2) respectively. XRD technique was used to identify the natural zeolite. Physicochemical characteristics of biodiesel were determined according to American Society for Testing and Materials (ASTM) standard methods and were found to be within ASTM permissible limits required for the operation of diesel engines except ash content. The element composition of synthesized biodiesel was investigated by Inductively Coupled Plasma. The synthesized biodiesel has been treated by different ratio of furfural. The best wt. % of furfural was found to be 66.6% (1:3, biodiesel: furfural). Treatment of Jatropha curcas L. biodiesel with furfural increased FAME and decreased alcohols, carbonyl, cyclic, and other compounds. Besides, furfural improved the physico-chemical characteristic of Jatropha curcas L. biodiesel within ASTM permissible limits. Cetane number has increased from 59.8 to 63.5 after treatment by 66.6% of furfural.