Experiments performed at TRIUMF and the Rutherford Appleton ISIS facility demonstrate the bias dependence of muon-induced single event upsets in delidded 28 nm static random access memories. Increased probability for upset is observed for memories operating at reduced voltages. Fully packaged parts are shown to be suitable to screen for low-energy muon sensitivity.
The thermal neutron soft error rate (SER) was measured systematically on SRAM cells in the technology range of 90 nm to 45 nm. We report here a substantial SER sensitivity with neutron energies below 0.4 eV for many SRAM cells.
In this work, VO2 thin films were deposited on Si wafers (onto (100) surface) by DC magnetron sputtering under different cathode bias voltages. The effects of substrate biasing on the structural and optical properties were investigated. The results show that the metal–insulator transition (MIT) temperature of VO2 thin films can be increased up to 14 K by applying a cathode bias voltage, compared to deposition conditions without any bias. The decrease in the transition efficiency and increase in the transition temperature are attributed to the enlarged grain size, increased defects, and the residual stress in the VO2 thin films induced by biasing. The optical transmittance measurements for different thickness films indicate an attenuation coefficient of 3.1 × 107 m−1 at 2000 nm or an extinction coefficient of 4.9 in the metal phase. The optical transmittance vs wavelength characteristics point to an indirect bandgap of 0.6 ± 0.05 eV and significant scattering in the bulk and/or at the interface.
4 March 2022 in IEEE Transactions on Device and Materials Reliability
The impact of Electromigration (EM) on the Bit-Error-Rate (BER) of signal interconnect paths was experimentally examined. An array-based test-vehicle for tracking Bit-Error-Rate (BER) degradation of signal interconnects subject to Direct-Current (DC) EM stress was implemented in a 16nm FinFET process. A unit interconnect path comprises five identical interconnect stages where each wire is driven by inverter based buffers. Accelerated EM stress testing is achieved entirely on-chip using metal heaters located directly above the devices-under-test (DUTs) and separate stress circuits driving both ends of the wire. The proposed test structure features a ring-based Voltage-Controlled-Oscillator (VCO), a bit-pattern generator and local BER sampling monitors which enable bitwise tracking of ’0’ and ’1’ errors separately, further simplifying the overall test-setup and allowing for high precision characterization of EM induced resistance shifts using only digital circuits. Measurement data collected from the 16nm prototype reveals unique insights into EM induced signal path degradation that was not available prior to this work. Our experimental studies suggest that monitoring the BER of an interconnect path could be used as a new metric for capturing EM induced resistance shifts in a real system, in lieu of the conventional approach which focuses on monitoring standalone wire resistances. Supplemental simulations showcasing the projected degradation in the interconnect path operating frequency as a function of stress time constructed from resistance traces sampled from identical wires implemented in the same process reaffirm the measurement trends.
1 October 2019 in Journal of Physics: Conference Series
Electrostatic discharge (ESD) shielding effectiveness of materials used to protect ESD sensitive devices was evaluated with a coaxial electrode and ESD generator. Attenuation of a continuous low power signal and a high power transient was measured. Electromagnetic far field shielding does not necessarily address ESD protection performance. High impedance on a discharge path reduces energy coupling efficiently. Therefore the prevention of conductive and capacitive coupling is the key factor for designing protective packaging for transportation of ESD sensitive devices. Due to the effect of breakdown field strength, low power signals shall not be used alone to assess ESD shielding characteristics. A coaxial electrode and an ESD generator was found a useful combination for the evaluation of ESD shielding effectiveness. As a final outcome, adequate ESD protection can be achieved even without the far field shielding, depending on application.
7 November 2019 in IEEE Transactions on Device and Materials Reliability
This study analyzes the Electrostatic Discharge (ESD) susceptibility of a 28 nm high-speed CMOS Integrated Circuit (IC) for network applications (25 Gbps), showing a non-negligible failure rate in manufacturing after having passed Charged Device Model (CDM) qualification testing. A detailed inspection of each process step identified the press-fit assembly of charged through-hole connectors to be the root cause for ultra-fast discharges through the Printed Circuit Board (PCB) traces into the high-speed RF interface. Extended CDM tests of the high-speed ICs displayed a wide overlap of pass and fail not allowing for a clear conclusion regarding the CDM robustness. Only the single digit ps-resolution and precision of the highly reproducible test method Capacitively Coupled Transmission Line Pulsing (CC-TLP) allowed a conclusive sharp pass/fail transition at a certain peak current level. In combination with a 33/63 GHz single shot oscilloscope, it eventually identified the stress current slew rate to have a direct influence on the failure threshold, explaining the non-conclusive failure distribution of CDM. For this result, we had to increase the bandwidth of the CC-TLP setup, challenge the limits of today's metrology and test setups, and implement post measurement embedding/de-embedding techniques. By pushing the frontiers of today's ESD testing in the CDM domain, the outcome of this study should contribute to future standardization of CDM and CC-TLP.
About Me
BS Chemical Eng, UC Berkeley
MS Electrical Eng ,Santa Clara Univ
Over 35 years experience in the semiconductor Industry
BS Chemical Eng, UC Berkeley
MS Electrical Eng ,Santa Clara Univ
Over 35 years experience in the semiconductor Industry