The paper presents the combustion profile of selected fuels as a result of thermogravimetric analysis. The main purpose of this study was to investigate a mixture of different types of fuel and the influence of the use of a fuel additive on the combustion process profile. As a fuel additive, halloysite was used to investigate the thermogravimetric profiles. It was confirmed that the main combustion parameters such as ignition temperature, burnout temperature, and maximum peak temperature correlated accordingly with different combustibility indices such as the ignition index, the burnout index, and the combustion indices. Furthermore, the present study provided a comparison of selected methods for analyzing non-isothermal solid-state kinetic data and investigated the kinetics of thermal decomposition to describe the ongoing process. Two non-isothermal model methods (Kissinger and Ozawa) were used to calculate the Arrhenius parameters. The effect of heating rate and the addition of halloysite as a fuel additive on decomposition were studied.
In the presented paper, two types of animal-origin biomass, cow dung and chicken litter, are characterized in terms of combustion-related problems and ash properties. It was found that these parameters strongly depend on the farming style. Whether it is cow dung or chicken litter, free-range raw materials are characterized by higher ash contents than industrial farming ones. Free-range samples contain chlorine at lower levels, while industrial farming samples are chlorine rich. Free-range samples are characterized by the predominant content of silica in the ash: 75.60% in cow dung and 57.11% in chicken litter, while industrial farming samples contain more calcium. Samples were classified by 11 “slagging indices” based on the ash and fuel composition to evaluate their tendencies for slagging, fouling, ash deposition and bed agglomeration. Furthermore, an assessment was made against the current EU law regulations, whether the ashes can be component materials for fertilizers. The phosphorus concentration in the investigated ashes corresponds to 4.09–23.73 wt% P2O5 and is significantly higher in industrial chicken litter samples. The concentrations of Hg, Cu, As, Ni, Cd and Pb in all samples are below the limits of the UE regulations. However, concentrations of Cr in all samples and Zn in industrial chicken litter exceed these standards.
An innovative dry SNCR method realized by a sorbent injection applied to a stoker furnace is presented. The process is based on urea powder admixed with halloysite, an aluminosilicate clay mineral. Field tests were performed at an industrial stoker hot water boiler of 30 MWth capacity. A unique nozzle design for injecting powdery sorbents into the combustion zone was implemented. The base NOx emission without SNCR was determined to be 365 mg/Nm3. During the reference test, the emission was reduced to avg. 175 mg/Nm3, which produces a NOx reduction of 52%. NH3 slip in the flue gas was stable and did not exceed 2 ppm. Combining urea and halloysite powders leads to a number of positive effects; not only is NOx emission reduced to values typical for wet SNCR, but also a significant, over ten-fold increase in the concentration of adsorbed mercury in fly ash was observed. When confronted with wet SNCR, dry SNCR has no adverse effect on boiler efficiency because it does not increase the stack heat loss. The presented method can be used in any small- or medium-scale furnace, including waste-to-energy units or medical and hazardous waste incineration units.
This paper presents a study of the fouling properties of solid fuels based on analyses of ashes from hard coal, forestry biomass, and agricultural biomass, ash deposits collected directly from the boiler surfaces, and ash deposits collected from a deposition probe. All samples were collected in the area of the steam superheater/reheater of a OP 380 pulverized-coal boiler co-firing forestry and agricultural biomass. In addition, the study concerns mitigation of unwanted fouling through application of a silica-based fireside additive. An analysis was carried out to obtain the following information: physical and chemical properties of ash produced during co-firing of a biomass mixture (50 wt.% forestry/50 wt.% agricultural biomass) and coal in order to determine its propensity for fouling and slagging without the use of a fireside additive; slagging/fouling indices during co-firing of a biomass mixture (50 wt.% forestry/50 wt.% agricultural biomass) and coal with the use of a fireside additive; and slagging/fouling indices during co-firing of pure agricultural biomass (sunflower husk) and coal with the use of a fireside additive. The mass flow of co-fired biomass fuel supplied to the boiler during reference measurements and mass flow when the additive was fed were the same and amounted to 33 wt.% of the total fuel mass flow. Finally, the effectiveness of fouling mitigation is determined by comparing the results of the deposition rate obtained with the use of a deposition probe for all three cases of co-firing.
1 March 2013 in Chemical and Process Engineering: New Frontiers
The paper deals with the impact of co-firing biomass with coal in boilers on the dew point of the flue gas. Co-firing of biomass may have twofold implications on corrosion and fouling, which are the processes that determine the lowest acceptable flue gas outlet temperature and as a result, boiler efficiency. Both phenomena may be reduced by co-firing of usually low sulphur biomasses or enhanced due to increased moisture content of biomass leading to increased water dew point. The present study concerns the problem of low-temperature corrosion in utility boilers. The paper gives (in the form of diagrams and equations) a relationship between water dew point and moisture content of fuel mixture when co-firing coal and various biomasses. The regression analysis shows that despite significant differences in the characteristics of coals and these of additional fuels, which are planned for co-firing in large-scale power boilers, the water dew point can be described by a function given with the accuracy, which shall be satisfactory for engineering purposes. The discussion of the properties of biofuels indicates that the acid dew point surplus over the water dew point (Δtr = tr - twr) is not likely to exceed 10 K when co-firing biomass. The concluding remarks give recommendations for the appropriate operation of boilers in order to reduce risks associated with biomass co-combustion.