An innovative dry SNCR method realized by a sorbent injection applied to a stoker furnace is presented. The process is based on urea powder admixed with halloysite, an aluminosilicate clay mineral. Field tests were performed at an industrial stoker hot water boiler of 30 MWth capacity. A unique nozzle design for injecting powdery sorbents into the combustion zone was implemented. The base NOx emission without SNCR was determined to be 365 mg/Nm3. During the reference test, the emission was reduced to avg. 175 mg/Nm3, which produces a NOx reduction of 52%. NH3 slip in the flue gas was stable and did not exceed 2 ppm. Combining urea and halloysite powders leads to a number of positive effects; not only is NOx emission reduced to values typical for wet SNCR, but also a significant, over ten-fold increase in the concentration of adsorbed mercury in fly ash was observed. When confronted with wet SNCR, dry SNCR has no adverse effect on boiler efficiency because it does not increase the stack heat loss. The presented method can be used in any small- or medium-scale furnace, including waste-to-energy units or medical and hazardous waste incineration units.
The application of secondary NOx control methods in medium to low-capacity furnaces is a relatively new topic on the energy market and thus requires further research. In this paper, the results of full-scale research of SNCR and hybrid SNCR + SCR methods applied into a 29 MWth solid fuel fired stoker boiler is presented. The tests were performed for a full range of boiler loads, from 33% (12 MWth) to 103% (30 MWth) of nominal load. A novel SNCR + SCR hybrid process was demonstrated based on an enhanced in-furnace SNCR installation coupled with TiO2-WO3-V2O5 catalyst, which provides extra NOx reduction and works as an excess NH3 “catcher” as well. The performance of a brand-new catalyst was evaluated in comparison to a recovered one. The emission of NOx was reduced below 180 mg NOx/Nm3 at 6% O2, with ammonia slip in flue gas below 10 mg/Nm3. Special attention was paid to the analysis of ammonia slip in combustion products: flue gas and fly ash. An innovative and cost-effective method of ammonia removal from fly ash was presented and tested. The main idea of this method is fly ash recirculation onto the grate. As a result, ammonia content in fly ash was reduced to a level below 6.1 mg/kg.
This paper presents experimental and analytical results of an investigation of heat transfer and pressure loss in a new type of convection heat exchanger tube bank with triple-finned tubes (TFTs). An initial evaluation of the optimal geometry of TFT banks using the Lusas code is presented. The heat transfer between the external environment and the medium inside the TFTs was modeled. Fins were arranged on a tube in the following three configurations: three fins with the same geometry with 45° between two symmetric fins and a vertical line of symmetry, denoted by T90, three fins with the same geometry with 30° between two symmetric fins and a vertical line of symmetry, denoted by T60, and one fin and angle steel plate placed parallel to the line of symmetry of the triple-finned tube, denoted by TAS90. The naphthalene sublimation technique is used as a heat/mass transfer analogy to evaluate the Sherwood (Nusselt) number ratios in the tube banks. The heat transfer performance of staggered S1T90 tube banks and the basic plain tube bank SP was compared. The second possibility for using TFTs is in a tube bank with all tubes finned was studied using the naphthalene analogy technique. The results are then compared with those computed using the computational fluid dynamics code. A comparison of the numerical and experimental heat transfer results shows that the trends in the heat transfer increase are very similar. The results show that triple-finned tubes can be used to increase the performance of cross-flow tube banks.
This paper presents the results of a numerical investigation into the use of window-blind-shaped inserts for enhancing heat transfer and facilitating fouling removal in cross-flow tube bundles. Three configurations were examined: a baseline staggered plain tube bundle, and the same staggered bundle equipped with steel window-blind inserts arranged in two distinct orientations: ( ) and ) (. The CFD simulations were performed using a two-dimensional model in Ansys Fluent. Tube bundles with inserts inclined at 5°, 20°, and 30° were analyzed for two flow velocities corresponding to maximum and minimum boiler loads. In addition, particle-trajectory simulations were conducted for the same blade inclinations to assess the potential for ash-deposit detachment. The results demonstrate that window-blind-type inserts can effectively enhance the thermal performance of tube bundles while simultaneously promoting the removal of ash deposits.