Mateusz Tymoszuk

Dr. Mateusz Tymoszuk

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2019 in Energy
Verified
Journal Article
Closed access
MTMateusz Tymoszuk
Mateusz Tymoszuk
KMKazimierz Mroczek
Kazimierz Mroczek
SKSylwester Kalisz
Sylwester Kalisz
HKHenryk Kubiczek
Henryk Kubiczek

1 November 2017 in Energy
Verified
Journal Article
Closed access
MPMarek Pronobis
Marek Pronobis
KMKazimierz Mroczek
Kazimierz Mroczek
MTMateusz Tymoszuk
Mateusz Tymoszuk
SCSzymon Ciukaj
Szymon Ciukaj
RWRobert Wejkowski
Robert Wejkowski
KJKatarzyna Jagodzińska
Katarzyna Jagodzińska

1 December 2015 in Energy
Verified
Journal Article
Closed access
SKSylwester Kalisz
Sylwester Kalisz
SCSzymon Ciukaj
Szymon Ciukaj
KMKazimierz Mroczek
Kazimierz Mroczek
MTMateusz Tymoszuk
Mateusz Tymoszuk
RWRobert Wejkowski
Robert Wejkowski
HKHenryk Kubiczek
Henryk Kubiczek

20 November 2021 in Energies
Verified
Journal Article
Open access
PDF file
RWRobert Wejkowski
Robert Wejkowski
Sylwester KaliszSylwester Kalisz
Sylwester Kalisz
MTMateusz Tymoszuk
Mateusz Tymoszuk
SCSzymon Ciukaj
Szymon Ciukaj
Izabella MajIzabella Maj
Izabella Maj
An innovative dry SNCR method realized by a sorbent injection applied to a stoker furnace is presented. The process is based on urea powder admixed with halloysite, an aluminosilicate clay mineral. Field tests were performed at an industrial stoker hot water boiler of 30 MWth capacity. A unique nozzle design for injecting powdery sorbents into the combustion zone was implemented. The base NOx emission without SNCR was determined to be 365 mg/Nm3. During the reference test, the emission was reduced to avg. 175 mg/Nm3, which produces a NOx reduction of 52%. NH3 slip in the flue gas was stable and did not exceed 2 ppm. Combining urea and halloysite powders leads to a number of positive effects; not only is NOx emission reduced to values typical for wet SNCR, but also a significant, over ten-fold increase in the concentration of adsorbed mercury in fly ash was observed. When confronted with wet SNCR, dry SNCR has no adverse effect on boiler efficiency because it does not increase the stack heat loss. The presented method can be used in any small- or medium-scale furnace, including waste-to-energy units or medical and hazardous waste incineration units.

14 November 2014 in Heat Transfer Engineering
Verified
Journal Article
Closed access
Sylwester KaliszSylwester Kalisz
Sylwester Kalisz
SCSzymon Ciukaj
Szymon Ciukaj
MTMateusz Tymoszuk
Mateusz Tymoszuk
HKHenryk Kubiczek
Henryk Kubiczek
This paper presents a study of the fouling properties of solid fuels based on analyses of ashes from hard coal, forestry biomass, and agricultural biomass, ash deposits collected directly from the boiler surfaces, and ash deposits collected from a deposition probe. All samples were collected in the area of the steam superheater/reheater of a OP 380 pulverized-coal boiler co-firing forestry and agricultural biomass. In addition, the study concerns mitigation of unwanted fouling through application of a silica-based fireside additive. An analysis was carried out to obtain the following information: physical and chemical properties of ash produced during co-firing of a biomass mixture (50 wt.% forestry/50 wt.% agricultural biomass) and coal in order to determine its propensity for fouling and slagging without the use of a fireside additive; slagging/fouling indices during co-firing of a biomass mixture (50 wt.% forestry/50 wt.% agricultural biomass) and coal with the use of a fireside additive; and slagging/fouling indices during co-firing of pure agricultural biomass (sunflower husk) and coal with the use of a fireside additive. The mass flow of co-fired biomass fuel supplied to the boiler during reference measurements and mass flow when the additive was fed were the same and amounted to 33 wt.% of the total fuel mass flow. Finally, the effectiveness of fouling mitigation is determined by comparing the results of the deposition rate obtained with the use of a deposition probe for all three cases of co-firing.

4 April 2025 in Energies
Verified
Journal Article
Open access
PDF file
MTMateusz Tymoszuk
Mateusz Tymoszuk
JWJoanna Wnorowska
Joanna Wnorowska
Sylwester KaliszSylwester Kalisz
Sylwester Kalisz
Economic and legal conditions of the European power industry enforce higher participation of biomass in the thermal energy mix per power unit, due to the necessity of carbon dioxide emission reduction. One of the most important features dictating the suitability of biomass fuel for utilization in pulverized fuel-fired boilers is its grindability. The grindability of biomass is a difficult parameter to estimate due to its non-uniform morphology and inhomogeneous character. Milling and co-milling of large amounts of biomass can deteriorate the mill output and make it difficult to ensure the proper particle size distribution of the pulverized fuel fed into the combustion chamber. The main objective was to determine whether torrefaction pre-treatments could increase the grindability features of various types of biomass. Investigations of raw and torrefied biomass grindability were performed with the use of a modified Hardgrove Index for alder chips, palm kernel shells, and willow chips. Additionally, semi-industrial scale milling tests were performed, which allowed for the evaluation of torrefied biomass suitability for continuous grinding installations equipped with vertical spindle mills. According to the analysis, an increase in the biomass grindability index after the torrefaction process was shown. Additionally, it was noted that for milling low-density materials (e.g., torrefied biomass), changes in the construction of the industrial mill classifier may be necessary for the proper grinding circuit operation.