The paper presents the combustion profile of selected fuels as a result of thermogravimetric analysis. The main purpose of this study was to investigate a mixture of different types of fuel and the influence of the use of a fuel additive on the combustion process profile. As a fuel additive, halloysite was used to investigate the thermogravimetric profiles. It was confirmed that the main combustion parameters such as ignition temperature, burnout temperature, and maximum peak temperature correlated accordingly with different combustibility indices such as the ignition index, the burnout index, and the combustion indices. Furthermore, the present study provided a comparison of selected methods for analyzing non-isothermal solid-state kinetic data and investigated the kinetics of thermal decomposition to describe the ongoing process. Two non-isothermal model methods (Kissinger and Ozawa) were used to calculate the Arrhenius parameters. The effect of heating rate and the addition of halloysite as a fuel additive on decomposition were studied.
The prediction of phase transformation of biomass ashes is challenging due to the highly variable composition of these fuels as well as the complex processes accompanying phase transformations. The AFT (Ash Fusion Temperature) model was performed in Statistica 13.1 software. This model was divided into three separate submodels, which were designed to predict the characteristic ash melting temperatures for raw and modified biomass. It is based on the chemical composition of fuel and ash as obtained using ash analysis standards. For the discussed models, several coefficients describing multiple regression parameters are presented. The AFT model discussed in this article is suitable for predicting ash fusion temperatures for biomass and allows for the prediction of the temperature with an average error of <±70.05 °C for IDT; <±51.98 °C for HT; <±47.52 °C for FT for raw biomass. For some of the additionally tested biomass, a value higher than the average difference between the measured temperature and the designated model was observed (<90 °C). Moreover, morphological analyses of the structure SEM-EDS for ash samples with and without additive were performed.
Economic and legal conditions of the European power industry enforce higher participation of biomass in the thermal energy mix per power unit, due to the necessity of carbon dioxide emission reduction. One of the most important features dictating the suitability of biomass fuel for utilization in pulverized fuel-fired boilers is its grindability. The grindability of biomass is a difficult parameter to estimate due to its non-uniform morphology and inhomogeneous character. Milling and co-milling of large amounts of biomass can deteriorate the mill output and make it difficult to ensure the proper particle size distribution of the pulverized fuel fed into the combustion chamber. The main objective was to determine whether torrefaction pre-treatments could increase the grindability features of various types of biomass. Investigations of raw and torrefied biomass grindability were performed with the use of a modified Hardgrove Index for alder chips, palm kernel shells, and willow chips. Additionally, semi-industrial scale milling tests were performed, which allowed for the evaluation of torrefied biomass suitability for continuous grinding installations equipped with vertical spindle mills. According to the analysis, an increase in the biomass grindability index after the torrefaction process was shown. Additionally, it was noted that for milling low-density materials (e.g., torrefied biomass), changes in the construction of the industrial mill classifier may be necessary for the proper grinding circuit operation.
Straw biomass is a renewable but problematic fuel due to its high alkali and chlorine content, which can cause slagging and corrosion during combustion. To mitigate these issues, this study investigates the influence of aluminosilicate additives on the thermal behavior and combustion characteristics of straw biomass. Laboratory-scale testing is carried out using thermogravimetric analysis under atmospheric air, showing the TG, DTG, and DSC profiles of samples (kaolinite, halloysite, straw biomass, and straw biomass with 4 wt.% of halloysite). Additionally, the main combustion parameters, like the ignition temperature, the maximum peak temperature, the burnout temperature, and some combustion indexes, are presented. The results show the effect of a heating rate in the range of 5–20 °C/min. Moreover, in this study, two non-isothermal model methods (Kissinger and Ozawa) are used to estimate energy activation. While halloysite slightly affects the combustion indexes and marginally reduces energy activation, its overall influence does not significantly alter combustion efficiency. These findings support the potential and safe use of halloysite for the biomass combustion process.
The article presents analysis of the particle size distribution inside pellets and the influence of moisture content before pelletization process on final product mechanical strength. The following types of biomass were used without and with the content of additive (halloysite): Polish wheat straw – (SP-K), miscanthus (DM), cereal straw (DS) and herbaceous pellets (BZ). Particles inside pellets were characterized by a grain size smaller than 3 mm and the cumulative weight percent passing through the sieve with mesh screen 1 mm for each sample was higher than 70 %. The moisture content before pelletization process for tested materials was in the range of 25% - 30% depending on the material which was used, while values of mechanical strength of pellets were within the range of 77.7% - 96.2% (depending on the type of material and moisture content before the pelletization process).