Jerzy Ratajski

Prof. Dr. Jerzy Ratajski

Department of Biomedical Engineering, Koszalin University of Technology, 75-453 Koszalin, Poland

Research Focus & Metrics

Academic Career Length

33Years (1994-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2012 in Vacuum
Verified
Journal Article
Closed access
BWBogdan Warcholinski
Bogdan Warcholinski
AGAdam Gilewicz
Adam Gilewicz
Jerzy RatajskiJerzy Ratajski
Jerzy Ratajski
ZKZ. Kuklinski
Z. Kuklinski
JRJ. Rochowicz
J. Rochowicz

1 August 2011 in Tribology International
Verified
Journal Article
Closed access
BWBogdan Warcholinski
Bogdan Warcholinski
AGAdam Gilewicz
Adam Gilewicz
Jerzy RatajskiJerzy Ratajski
Jerzy Ratajski


1 August 2003 in Surface Engineering
Verified
Journal Article
Closed access
Jerzy RatajskiJerzy Ratajski
Jerzy Ratajski
JTJ. Tacikowski
J. Tacikowski
Marcel A.J. SomersMarcel A.J. Somers
Marcel A.J. Somers
The composition and phase constitution of a compound layer developing during gaseous nitriding was investigated at 853 K for three commercial steels (AISI 120, 4340 and 1090) and Armco iron. The compound layers were characterised by light optical microscopy, X-ray diffraction and electron probe microanalysis. The formation of the compound layer occurs along two distinct sequences: α→γ′→ϵ and/or α ( θ)→ϵ2→γ′→ϵ1. The preferred sequence depends mainly on the chemical composition of steel and on the nitriding potential.

17 May 2024 in Materials
Verified
Journal Article
Open access
PDF file
Jerzy RatajskiJerzy Ratajski
Jerzy Ratajski
Błażej BałaszBłażej Bałasz
Błażej Bałasz
KMKatarzyna Mydłowska
Katarzyna Mydłowska
Mieczysław PancielejkoMieczysław Pancielejko
Mieczysław Pancielejko
ŁSŁukasz Szparaga
Łukasz Szparaga
In this article, the results of research on a NiTi alloy with a high nickel content (51.7 at.%), produced using the additive technology SLM method and subjected to isothermal ageing after solution annealing, are presented. The study involved the determination of the sequence of phase transformations occurring using differential scanning calorimetry (DSC) and the determination of the temperature range of these transformations. In parallel, the phase composition was determined using the XRD method; the hardness and the Young’s modulus were also determined. The analysis of the DSC results obtained indicates the following characteristic features of the NiTi alloy, which change with ageing time: (1) During cooling (from +150 °C to −50 °C), the type of transformation changes from a one-step transformation after solution annealing to a two-step transformation after the ageing process over 1, 20, and 100 h at 500 °C; (2) during heating (from −50 °C to +150 °C) for all the samples, regardless of the ageing time, only a one-step transformation from martensite M(B19′) to austenite A(B2) is observed; (3) the temperature at which the transformation starts increases with the ageing time; (4) the width of the total temperature range of the transformation M(B19′) → A(B2) during heating changes from large (ΔT = 49.7 °C), after solution annealing, to narrow (ΔT = 19.3 °C and ΔT = 17.9 °C after 20 h and 100 h of ageing); and, most importantly, (5) a comparison with the literature data shows that, irrespective of the composition of the NiTi alloy and the manufacturing technology of the alloy samples (regardless of whether this was traditional or additive technology), a sufficiently long ageing process period leads to the occurrence of the martensite → austenite transformation in the same temperature range.

23 March 2017 in Protection of Metals and Physical Chemistry of Surfaces
Verified
Journal Article
Closed access
PDF file
AGAdam Gilewicz
Adam Gilewicz
DMD. Murzynski
D. Murzynski
Ewa DobruchowskaEwa Dobruchowska
Ewa Dobruchowska
JKJ. Kwiatkowski
J. Kwiatkowski
ROR. Olik
R. Olik
BWBogdan Warcholinski
Bogdan Warcholinski
In the paper, the results of wear and corrosion tests of the CrCN/CrN multilayer coatings, formed by cathodic arc evaporation on 42CrMo4 (AISI 4140) steel substrates are presented. The substrates were subjected to thermo-chemical treatment–nitriding with various nitriding potential. The results of nitriding were determined by XRD and the hardness profile in the samples cross-section. The morphology of thin coatings was examined with SEM. A Vickers FV-700 and Fisherscope HM2000 hardness testers enabled to investigate hardness of steel substrates and CrCN/CrN coatings respectively. A pin-on-disc wear tests were used to determine the hardness and tribological parameters of the coatings: the coefficient of the friction and wear rate. The scratch test and Rockwell test were applied to assess the adhesion of the coatings to the substrates. The corrosion properties of coating–steel substrate systems were investigated using potentiodynamic polarisation tests. Corrosion potential, corrosion current density and polarization resistance were determined. It was found that that the nitriding of steel substrates improves properties of the coating–substrate system. The nitriding 42CrMo4 steel substrate with low nitriding potential enable to obtain substrates without surface “white layer” what favours good adhesion of the coating to the substrate. The CrCN/CrN multilayer coating–steel substrate systems show good mechanical and tribological properties and corrosion resistance.