Antonín Lokaj

Prof. Dr. Antonín Lokaj

Professor at University
orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 December 2020 in Materials
Verified
Journal Article
Open access
PDF file
Antonín LokajAntonín Lokaj
Antonín Lokaj
Pavel DobešPavel Dobeš
Pavel Dobeš
Oldrich SuchardaOldrich Sucharda
Oldrich Sucharda
This article presents the results of static tests on bolted connections in squared and round timber with inserted steel plates. The experiment evaluates structural timber connections with different distances between the fastener and the loaded end at different moisture contents. Specimens were loaded by tension parallel to the grain and load–deformation diagrams were recorded. Fifty-six specimens with three different distances between the fastener and the loaded end, at different moisture contents, were tested. The results were statistically evaluated using regression analysis, complemented with load–deformation curves, and compared with calculations according to the valid standard for design of timber structures. A decrease in the evaluated load-carrying capacity with increasing moisture content was confirmed experimentally. A slight increase in the evaluated load-carrying capacity with increasing fastener distance from the loaded end was found.

1 October 2011 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
Antonín LokajAntonín Lokaj
Antonín Lokaj
Kristýna VavrušováKristýna Vavrušová
Kristýna Vavrušová
EREva Rykalová
Eva Rykalová
The aim of this paper is determination of selected strength characteristics of dowel joints in cement-splinter boards VELOX on the basis of destructive testing and application of these results into the fully probabilistic SBRA method (Simulation Based Reliability Assessment).

25 December 2020 in Sustainability
Verified
Journal Article
Open access
PDF file
MJMarek Johanides
Marek Johanides
LKLenka Kubíncová
Lenka Kubíncová
DMDavid Mikolasek
David Mikolasek
Antonín LokajAntonín Lokaj
Antonín Lokaj
Oldrich SuchardaOldrich Sucharda
Oldrich Sucharda
Petr MynarcikPetr Mynarcik
Petr Mynarcik
Initially, timber was considered only as an easily accessible and processable material in nature; however, its excellent properties have since become better understood. During the discovery of new building materials and thanks to new technological development processes, industrial processing technologies and gradually drastically decreasing forest areas, wood has become an increasingly neglected material. Load-bearing structures are made mostly of reinforced concrete or steel elements. However, ecological changes, the obvious problems associated with environmental pollution and climate change, are drawing increasing attention to the importance of environmental awareness. These factors are attracting increased attention to wood as a building material. The increased demand for timber as a building material offers the possibility of improving its mechanical and physical properties, and so new wood-based composite materials or new joints of timber structures are being developed to ensure a better load capacity and stiffness of the structure. Therefore, this article deals with the improvement of the frame connection of the timber frame column and a diaphragm beam using mechanical fasteners. In common practice, bolts or a combination of bolts and pins are used for this type of connection. The subject of the research and its motivation was to replace these commonly used fasteners with more modern ones to shorten and simplify the assembly time and to improve the load capacity and rigidity of this type of frame connection.

11 January 2023 in Buildings
Verified
Journal Article
Open access
PDF file
Pavel DobešPavel Dobeš
Pavel Dobeš
Antonín LokajAntonín Lokaj
Antonín Lokaj
Kristýna VavrušováKristýna Vavrušová
Kristýna Vavrušová
Timber structures are currently more important for solving tasks in construction practice. For this reason, there is an opportunity for research in the area of physical tests and numerical models. This paper deals with the determination and comparison of the deformation properties of cross-laminated timber (CLT) panels based on laboratory tests, analytical calculation and numerical modeling. CLT panels are structural building components consisting of cross-oriented solid timber layers. Three types of panels with different geometry and number of layers (three, five and seven) were experimentally tested using a four-point bending test, where load–deformation curves were recorded. The results of the experimental testing of the three-layer panels were subsequently compared with a numerical model in SCIA Engineer, a numerical model in ANSYS Workbench and an analytical calculation. The research shows a good agreement in bending behavior between the laboratory tests, the analytical calculation according to the standard and two different approaches in numerical analysis.

7 April 2022 in Materials
Verified
Journal Article
Open access
PDF file
Pavel DobešPavel Dobeš
Pavel Dobeš
Antonín LokajAntonín Lokaj
Antonín Lokaj
DMDavid Mikolasek
David Mikolasek
Nowadays, the use of timber as a building material is gaining more prominence. When designing timber structures, it is necessary to pay increased attention to the design of their connections. The commonly used connections are dowel-type connections, which are often used in combination with steel plates slotted into cut-outs in timber members. The presented paper deals with the behavior of double-shear bolted connections of squared timber and round timber with slotted-in steel plates. Several variants of connections with different distances between the fastener and the loaded end were selected for the experimental testing. A total of six types of test specimens were made from spruce timber, for which their selected physical properties were determined and evaluated before the experimental testing. Test specimens of bolted connections were first tested in tension parallel to the grain until failure under quasi-static loading. The connections were broken by splitting. Ductile failure preceded brittle failure. The actual load-carrying capacities were lowest for the lowest end distance. The load-carrying capacities for the middle and the longest end distances were comparable. The results of the experiments were then used for comparison with calculation procedures according to the standard for the design of timber structures and with calculations according to the theory of linear elastic fracture mechanics. The experiments and the analytical models were supported by a simple numerical analysis based on the finite element method.

1 November 2013 in Advanced Materials Research
Verified
Journal Article
Closed access
PDF file
PKPetr Kučera
Petr Kučera
Antonín LokajAntonín Lokaj
Antonín Lokaj
VVVladimír Vlček
Vladimír Vlček
In the presented paper is comprehensively assessed the behavior of spruce and birch wood during fire. Samples were loaded by heat flux of 20, 35 and 50 kW/m2in apparatus according to ISO 5657. The duration of the test was up to 30 min. The behavior of the samples was evaluated on the basis of charring rate and concentrations of carbon monoxide in smoke. Charring rate was rising with increasing heat flux density and decreasing linearly with increasing density of the samples. The maximum concentration of CO in the smoke for spruce and birch wood was observed just before the end of the test, during the phase of char layer burning.