This study focuses on the effect of part geometry and infill degrees on effective mechanical properties of extrusion additively manufactured stainless steel 316L parts produced with BASF’s Ultrafuse 316LX filament. Knowledge about correlations between infill degrees, mechanical properties and dimensional deviations are essential to enhance the part performance and further establish efficient methods for the product development for lightweight metal engineering applications. To investigate the effective Young’s modulus, yield strength and bending stress, standard testing methods for tensile testing and bending testing were used. For evaluating the dimensional accuracy, the tensile and bending specimens were measured before and after sintering to analyze anisotropic shrinkage effects and dimensional deviations linked to the infill structure. The results showed that dimensions larger than 10 mm have minor geometrical deviations and that the effective Young’s modulus varied in the range of 176%. These findings provide a more profound understanding of the process and its capabilities and enhance the product development process for metal extrusion-based additive manufacturing.
As an alternative to powder-bed based processes, metal parts can be additively manufactured by extrusion based additive manufacturing. In this process, a highly filled polymer filament is deposited and subsequently debindered and sintered. Choosing a proper orientation of the part that satisfies the requirements of the debinding and sintering processes is crucial for a successful manufacturing process. To determine the optimal orientation for debinding, first, the part must be scaled in order to compensate the sinter induced shrinkage. Then, a finite element analysis is performed to verify that the maximum stresses due to the dead load do not exceed the critical stress limits. To ease this selection process, an approach based on open source software is shown in this article to efficiently determine a part’s optimal orientation during debinding. This automates scaling, debinding simulation, and postprocessing for all six main directions. The presented automated simulation framework is examined on three application examples and provides plausible results in a technical context for all example parts, leading to more robust part designs and a reduction of experimental trial and error. Therefore, the presented framework is a useful tool in the product development process for metal extrusion additive manufacturing applications.
Hierarchical structures are abundant in almost all tissues of the human body. Therefore, it is highly important for tissue engineering approaches to mimic such structures if a gain of function of the new tissue is intended. Here, the hierarchical structures of the so-called enthesis, a gradient tissue located between tendon and bone, were in focus. Bridging the mechanical properties from soft to hard secures a perfect force transmission from the muscle to the skeleton upon locomotion. This study aimed at a novel method of bioprinting to generate gradient biomaterial constructs with a focus on the evaluation of the gradient printing process. First, a numerical approach was used to simulate gradient formation by computational flow as a prerequisite for experimental bioprinting of gradients. Then, hydrogels were printed in a single cartridge printing set-up to transfer the findings to biomedically relevant materials. First, composites of recombinant spider silk hydrogels with fluorapatite rods were used to generate mineralized gradients. Then, fibroblasts were encapsulated in the recombinant spider silk-fluorapatite hydrogels and gradually printed using unloaded spider silk hydrogels as the second component. Thereby, adjustable gradient features were achieved, and multimaterial constructs were generated. The process is suitable for the generation of gradient materials, e.g., for tissue engineering applications such as at the tendon/bone interface.
Topology optimization is a powerful digital engineering tool for the development of lightweight products. Nevertheless, the transition of obtained design proposals into manufacturable parts is still a challenging task. In this article, the development of a freeware framework is shown, which uses a hybrid topology optimization algorithm for stiffness and strength combined with manufacturing constraints based on finite spheres and a two-step smoothing algorithm to design manufacturable prototypes with “one click”. The presented workflow is shown in detail on a rocker, which is “one-click”-optimized and manufactured. These parts were experimentally tested using a universal testing machine. The objective of this article was to investigate the performance of “one-click”-optimized parts in comparison with manually redesigned optimized parts and the initial design space. The test results show that the design proposals created while applying the finite-spheres and two-step smoothing are equal to the manual redesigned parts based on the optimization results, proposing that the “one-click”-development can be used for the fast and direct development and fabrication of prototypes.
Additive manufacturing is a potentially disruptive technology with a high impact on supply chains and part design. While generally allowing much higher degrees of freedom in design than formative and subtractive manufacturing techniques, the necessity of support structures can diminish the impact of additive manufacturing. This article presents a methodology based on finite spheres to integrate knowledge about process limitations into topology optimization for the direct extrusion-based additive manufacturing of parts with maximized stiffness and strength and minimized support structures. This methodology has been included within our self-developed Freeware Z88 Arion® V3. We investigated the impact of the manufacturing constraints on the additive manufacturing process regarding effective material usage on application test examples. The test results showed that the design proposals created while applying the finite spheres and two-step smoothing needed significantly less or no support material for all application examples.
About Me
Senior Engineer, research interests engineering with polymers, optimization, additive manufacturing
Senior Engineer, research interests engineering with polymers, optimization, additive manufacturing