The structural optimization of manufacturable casting parts is still a challenging and time-consuming task. Today, topology optimization is followed by a manual reconstruction of the design proposal and a process assurance simulation to endorse the design proposal. Consequently, this process is iteratively repeated until it reaches a satisfying compromise. This article shows a method to combine structural optimization and process assurance results to generate automatically structure- and process-optimized die casting parts using implicit geometry modeling. Therefore, evaluation criteria are developed to evaluate the current design proposal and qualitatively measure the improvement of manufacturability between two iterations. For testing the proposed method, we use a cantilever beam as an example of proof. The combined iterative method is compared to manual designed parts and a direct optimization approach and evaluated for mechanical performance and manufacturability. The combination of topology optimization (TO) and process assurance (PA) results is automated and shows a significant enhancement to the manual reconstruction of the design proposals. Further, the improvement of manufacturability is better or equivalent to previous work in the field while using less computational effort, which emphasizes the need for suitable metamodels to significantly reduce the effort for process assurance and enable much shorter iteration times.
2 March 2024 in International Journal of Metalcasting
The multi-material injector casting (MMIC) process allows the production of castings with two different alloys in a single process. The metal is introduced into the mold through a ceramic down sprue (injector) that moves with the rising surface of the melt. This results in a beneficial temperature distribution in the casting with enhanced filling and feeding properties. Combining two alloys in one casting affects the chemical composition, microstructure, and mechanical properties, which differ from those of the original alloys. The main goal of producing the dual-alloy castings is to adapt the alloy locally in the mixing zone according to the application needs. The original composition and characteristics of both alloys have to be ensured as much as possible. This article discusses the peculiarities of dual-alloy sand mold casting, considering the oxidation processes of the components under different conditions and the microstructure of the resulting ingots. The results of thermodynamic simulation, experimental dual-alloy sand mold casting, chemical composition, and macrostructure of the resulting castings are given in the article. The following factors have been investigated: the method of pouring two alloys (AlSi12 and AlSi9Cu3), which simulate two injector positions; the time between pouring each alloy (60, 90, and 120 s); the influence of a directional solidification with the bottom chill. The mixing zone was identified by the changes in the content of Cu measured by spark spectroscopy and EDS.
22 November 2025 in International Journal of Metalcasting
In the multi-material injector casting process, two different melts are cast consecutively into a mold through a ceramic injector. The current work comprises the manufacturing and characterization of Al/Al double-alloy castings using this novel process. The experimental setup is described, and castings consisting of EN AC-AlSi9Cu3(Fe) and EN AC-AlSi12(a) are fabricated. The influence of the time interval between casting both alloys on the mixing behavior and mechanical properties is investigated. Optical inspection and spark spectrometry testing showed the realization of multi-material components characterized by a vertical material gradient. The transition zone is investigated by tensile and torsion tests. In both experiments, the specimens failed predominantly in the weaker material, AlSi12. An early failure of the cohesive transition zone is not detected. The utilization of a digital image correlation system reveals a locally varying deformation behavior of the specimens during the tensile experiments.
1 May 2023 in IOP Conference Series: Materials Science and Engineering
Castings are predestined for the application of structural optimization, but to date, the integration of process simulation into structural optimization is limited due to high computational cost and is therefore often neglected at the beginning of the design process. This leads to the need for surrogate models, which allow a fast and simplified evaluation of design proposals during the optimization in order to improve the integration. This article introduces a novel approach that estimates the solidification time of randomly created geometries solely based on the casting geometry. The approach uses ray-tracing methods to calculate the distance function along preset directions. The estimated solidification time is calculated using a Spherical Convolutional Neural Network (CNN). The training data is obtained by several thousand solidification simulations using the optimization toolkit of a commercial casting simulation software combined with further data augmentation. The model is experimentally validated for five different geometries in the sand casting process.