Epoxy composite coating systems generally find their usage in applications such as, fluid handling systems to protect components from corrosive media. However, their use in demanding tribological applications such as, in sliding components of machines, are known to be limited. This is often attributed to their low load bearing capacity combined with poor thermal stability under severe p-v regimes. Researchers have tried to enhance the tribological properties of the epoxy coatings using a combination of several types of micro/nano sized fillers to produce composite or hybrid composite coatings. Hence, this review paper aims to focus on the recent advances made in developing the epoxy coating systems. Special attention would be paid to the types and properties of nano-fillers that have been commonly used to develop these coatings, different dispersion techniques adopted and the effects that each of these fillers (and their combinations) have on the tribological properties of these coatings.
Heat sinks are commonly used for cooling electronic devices and high-power electrical systems. The ever-increasing performance of electronic systems together with miniaturization calls for better heat dissipation. Therefore, the heat sink materials should not only have high thermal conductivities, low densities, and cost, but also have coefficients of thermal expansion matching to those of semiconductor chips and ceramic substrates. As traditional materials fail to meet these requirements, new composite materials have been developed with a major focus on metal matrix composites (MMCs). MMCs can be tailored to obtain the desired combination of properties by selecting proper metallic matrix and optimizing the size and type, volume fraction, and distribution pattern of the reinforcements. Hence, the current review comprehensively summarizes different studies on enhancing the thermal performance of metallic matrices using several types of reinforcements and their combinations to produce composites. Special attention is paid to the types of commonly used metallic matrices and reinforcements, processing techniques adopted, and the effects of each of these reinforcements (and their combinations) on the thermal properties of the developed composite. Focus is also placed on highlighting the significance of interfacial bonding in achieving optimum thermal performance and the techniques to improve interfacial bonding.
An attempt is made to cover the whole of the topic of biodegradable magnesium (Mg) alloys with a focus on the biocompatibility of the individual alloying elements, as well as shed light on the degradation characteristics, microstructure, and mechanical properties of most binary alloys. Some of the various work processes carried out by researchers to achieve the alloys and their surface modifications have been highlighted. Additionally, a brief look into the literature on magnesium composites as also been included towards the end, to provide a more complete picture of the topic. In most cases, the chronological order of events has not been particularly followed, and instead, this work is concentrated on compiling and presenting an update of the work carried out on the topic of biodegradable magnesium alloys from the recent literature available to us.
Due to rapid technological advancements, the demand for lightweight materials with improved tribo-mechanical properties is continuously growing. The development of composite materials is one of the routes taken by researchers to meet these target properties. Aluminum (Al) is one of the most suitable materials used for developing composites for a wide range of applications because of its light weight, high conductivity, and high specific strength. In this study, aluminum hybrid nanocomposites with alumina (10 Vol% Al2O3) and varying loadings of graphene oxide (0.25, 0.5 and 1 wt% GO) were fabricated using the spark plasma sintering technique. The tribological properties of the developed hybrid composites were evaluated by conducting ball-on-disk wear tests at a normal load of 3N, with a sliding speed of 0.1 m/s, and for a sliding distance of 100 m. A 440C hardened stainless steel ball with a diameter of 6.3 mm and a hardness of 62 RC was used as a counterface. Scanning electron microscopy (SEM), elemental X-ray dispersive analysis (EDS), and optical profilometry were used to ascertain the involved wear mechanisms. The results revealed that Al-10 Vol%Vol% Al2O3-0.25 wt% GO hybrid nanocomposite showed an increase of 48% in the hardness, a reduction of 55% in the specific wear rate, and a reduction of 5% in COF compared with pure aluminum.
To understand and quantify casing wear during drilling operations, an experimental setup with real drill pipe joints (DPJ) and casings was designed and used to carry out wear tests, simulating various operating conditions and environments. P110 steel casing samples were tested under dry and wet conditions. Actual field oil- and water-based fluids were utilized to lubricate the contact area at two different side loads (1000 N and 1400 N) and DPJ speeds (115 and 207 rpm). The results show that for the same testing conditions, the casing wear volume and wear factor under water-based lubrication were more than twice those obtained under oil-based fluid testing. As expected, the wear volume and wear factor were highest under dry conditions. Moreover, it was noticed that, as the normal load was increased at a constant rotational speed (rpm), the wear factor increased. On the other hand, raising the rotational speed at the same applied load reduced the casing wear factor, due to the observed absence of adhesive wear and possible localized softening effects at higher speeds. SEM analyses of the worn areas showed that under dry conditions, the main wear mechanisms were abrasion and delamination. However, both adhesive wear and abrasive wear mechanisms were observed under oil-based lubrication. The energy dispersive spectroscopy (EDS) analysis of the worn surface revealed that at higher loads and speeds, a heavy transfer of particles from the oil-based lubricant took place. On the other hand, some contaminants of the water-based lubricant were observed on the worn surfaces.
Polymer coatings have gained a lot of attention in the recent past because of their ability to be easily coated on complex shapes, their low cost, and their ability to reduce friction as compared to other materials. Polyether ether ketone (PEEK) is one such high-performance polymer that has gained significant attention in recent years due to its exceptional mechanical properties, chemical resistance, and thermal stability making it a prominent candidate for applications in industries. However, PEEK in its pristine form exhibits poor wear resistance with a moderate coefficient of friction (0.30–0.38). Many attempts have been made by several researchers to improve its wear resistance and lower the COF by developing composite coatings. Hence, in this review, we aim to summarize and present in detail the tribological evaluation of pristine PEEK and PEEK composite coatings by discussing the various methods adopted by the researchers to improve the properties of PEEK, the different types of reinforcements and various dispersion techniques used to develop PEEK composite coatings. By consolidating and analyzing the existing body of knowledge, we also aim to offer valuable insights into the development of more durable, high-performance PEEK nanocomposite coatings for a broad range of tribological applications.