In this review, the 3D printing techniques on fabricating complex structures for electromagnetic wave absorbing and/or shielding, as well as the current challenges and future prospects, are emphatically summarized.
Piezoelectric accelerometers present higher sensitivities and better signal-to-noise ratios in comparison with piezoresistive and capacitive accelerometers. A micro-electromechanical system (MEMS) piezoelectric accelerometer was designed and manufactured with four L-shaped beams covered by Lead Zirconate Titanate (PZT) thin film with $1~\mu \text{m}$ in thickness which was deposited using sol-gel methods. The micro devices, whose size and the optimized PZT distribution were determined by theoretical and simulation analysis, were fabricated on the silicon substrate using PZT films working in the ${d}_{31}$ mode. Different from the conventional vertical crossbeam accelerometers, the designed structure devotes to the larger area piezoelectric film laid on L-shaped supporting beams with higher energy transferring efficiency for sensing. Then the chips of accelerometer were fabricated, and the proposed sensor was packaged on the printed circuit board (PCB). In addition, the microsphere was integrated in the center of the beams. Finally, the properties of the accelerometer were measured by vibration measurement system. The measuring results show that the initial sensitivity of the accelerometer is 28.14mV/g at 500Hz. The proposed piezoelectric accelerometer has high sensitivity and low resonance frequency, and the frequency response on each beam is consistent, providing a new structure for high-performance accelerometer.
Harvesting low-frequency vibration energy in the environment can provide electrical energy for mobile electronic devices. In this article, a bidirectional driving vibration energy harvester is presented based on the electromagnetic induction. The bidirectional driving component of the energy harvester converts the reciprocating linear motion driving energy into the unidirectional rotation. In addition, the two sets of generators are rectified first, and then connected in series to reduce the voltage rang, which is conducive to energy management and storage, and reduces energy loss. The results show that its average output power is 53.28 mW when the acceleration is 9 m/s 2 . At a running speed of 8 km/h, the average output power of the energy harvester installed on the human torso is 41.07 mW. At the same time, it can provide real-time energy supply for temperature hygrometer, calculator, and Bluetooth module. It is a novel method for the harvest and utilization of vibration energy, and has great significance for solving the current energy long-term demand of electronic devices.
Graphene-based metamaterials have been widely applied in optoelectronic devices, optical modulators, and chemical sensors due to the outstanding tunability and optical response in the terahertz (THz) region. Here, tunable THz metamaterial absorbers based on patterned graphene are designed, fabricated, and modulated. The proposed metamaterial absorbers are constructed by the top layer of patterned graphene arrays and the aluminum (Al) film separated by polyimide (PI). The different THz absorption spectra can be acquired by changing the patterns of graphene. In order to verify the simulation results, a series of tests were conducted by THz time-domain spectrometer (THz-TDS) systems. The proposed absorbers are able to be insensitive to the angle of the incident wave. Besides, chemical doping is applied to turn the Fermi level of graphene and the absorption performance is promoted with the increase of the Fermi level. The experimental results have been demonstrated to have associated resonant peaks with the simulation results. The aim of this paper is to exhibit a systematic study on graphene-based THz metamaterial absorbers, including the simulation and experiments. By comparing the simulation and experimental results, it is useful to clarify the relevant theories and manufacturing processes. The work will provide a further step in the development of high-performance terahertz devices, including tunable absorbers, sensors, and electro-optic switches.
Domain wall current (DWC) plays a key role in storage devices, logic devices and sensors due to its high on-off ratio and nano structure size in the era of nanoelectronics technology. In this work, the DWC of single crystal LiNbO 3 thin film was studied by piezoresponse force microscope (PFM) and conducting atomic force microscope (c-AFM). We mainly focus on voltage and temperature dependence of DWC which increases with the voltage and temperatures. Based on this research, the packaged DWC temperature sensor is fabricated and applied in wide temperature range. The existence of domain walls makes the current on-off ratio as high as 10 3 at the voltage of 15 V. Our study shows that DWC has a negative temperature coefficient (NTC) from 140 K to 500 K. The current increases from 3 pA to $57 ~\mu \text{A}$ , which is attributed to the conductivity of switched domain. This work proposes a new type temperature sensor with wide temperature range and high compatibility and sensitivity. In addition, it provides support for harsh environment applications of ferroelectric domain engineering devices.