Graphene-based metamaterials have been widely applied in optoelectronic devices, optical modulators, and chemical sensors due to the outstanding tunability and optical response in the terahertz (THz) region. Here, tunable THz metamaterial absorbers based on patterned graphene are designed, fabricated, and modulated. The proposed metamaterial absorbers are constructed by the top layer of patterned graphene arrays and the aluminum (Al) film separated by polyimide (PI). The different THz absorption spectra can be acquired by changing the patterns of graphene. In order to verify the simulation results, a series of tests were conducted by THz time-domain spectrometer (THz-TDS) systems. The proposed absorbers are able to be insensitive to the angle of the incident wave. Besides, chemical doping is applied to turn the Fermi level of graphene and the absorption performance is promoted with the increase of the Fermi level. The experimental results have been demonstrated to have associated resonant peaks with the simulation results. The aim of this paper is to exhibit a systematic study on graphene-based THz metamaterial absorbers, including the simulation and experiments. By comparing the simulation and experimental results, it is useful to clarify the relevant theories and manufacturing processes. The work will provide a further step in the development of high-performance terahertz devices, including tunable absorbers, sensors, and electro-optic switches.
It is a great challenge to detect in-situ high-frequency vibration signals for extreme environment applications. A highly sensitive and robust vibration sensor is desired. Among the many piezoelectric materials, single-crystal lithium niobate (LiNbO3) could be a good candidate to meet the demand. In this work, a novel type of micro-electro-mechanical system (MEMS) vibration sensor based on a single crystalline LiNbO3 thin film is demonstrated. Firstly, the four-cantilever-beam MEMS vibration sensor was designed and optimized with the parametric method. The structural dependence on the intrinsic frequency and maximum stress was obtained. Then, the vibration sensor was fabricated using standard MEMS processes. The practical intrinsic frequency of the as-presented vibration sensor was 5.175 kHz, which was close to the calculated and simulated frequency. The dynamic performance of the vibration sensor was tested on a vibration platform after the packaging of the printed circuit board. The effect of acceleration was investigated, and it was observed that the output charge was proportional to the amplitude of the acceleration. As the loading acceleration amplitude is 10 g and the frequency is in the range of 20 to 2400 Hz, the output charge amplitude basically remains stable for the frequency range from 100 Hz to 1400 Hz, but there is a dramatic decrease around 1400 to 2200 Hz, and then it increases significantly. This should be attributed to the significant variation of the damping coefficient near 1800 Hz. Meanwhile, the effect of the temperature on the output was studied. The results show the nearly linear dependence of the output charge on the temperature. The presented MEMS vibration sensors were endowed with a high output performance, linear dependence and stable sensitivity, and could find potential applications for the detection of wide-band high-frequency vibration.
The substrate impurities scattering will lead to unstable temperature-sensitive behavior and poor linearity in graphene temperature sensors. And this can be weakened by suspending the graphene structure. Herein, we report a graphene temperature sensing structure, with suspended graphene membranes fabricated on the cavity and non-cavity SiO2/Si substrate, using monolayer, few-layer, and multilayer graphene. The results show that the sensor provides direct electrical readout from temperature to resistance transduction by the nano piezoresistive effect in graphene. And the cavity structure can weaken the substrate impurity scattering and thermal resistance effect, which results in better sensitivity and wide-range temperature sensing. In addition, monolayer graphene is almost no temperature sensitivity. And the few-layer graphene temperature sensitivity, lower than that of the multilayer graphene cavity structure (3.50%/°C), is 1.07%/°C. This work demonstrates that piezoresistive in suspended graphene membranes can effectively enhance the sensitivity and widen the temperature sensor range in NEMS temperature sensors.
As a promising functional material, ferroelectric Pb(ZrxTi1−x)O3 (PZT) are widely used in many optical and electronic devices. Remarkably, as the film thickness decreases, the materials’ properties deviate gradually from those of solid materials. In this work, multilayered PZT thin films with different thicknesses are fabricated by Sol-Gel technique. The thickness effect on its microstructure, ferroelectric, and optical properties has been studied. It is found that the surface quality and the crystalline structure vary with the film thickness. Moreover, the increasing film thickness results in a significant increase in remnant polarization, due to the interfacial layer effect. Meanwhile, the dielectric loss and tunability are strongly dependent on thickness. In terms of optical properties, the refractive index of PZT films increase with the increasing thickness, and the photorefractive effect are also influenced by the thickness, which could all be related to the film density and photovoltaic effect. Besides, the band gap decreases as the film thickness increases. This work is significant for the application of PZT thin film in optical and optoelectronic devices.
The seeking of resonator with high Q and low insertion loss is attractive for critical sensing scenes based on the surface acoustic wave (SAW). In this work, 128° YX LiNbO3-based SAW resonators were utilized to optimize the output performance through IDT structure parameters. Once the pairs of IDTs, the acoustic aperture, the reflecting grid logarithm, and the gap between IDT and reflector are changed, a better resonance frequency of 224.85 MHz and a high Q of 1364.5 were obtained. All the results demonstrate the structure parameters design is helpful for the performance enhancement with regard to SAW resonators, especially for designing and fabricating high-Q devices.
3 April 2020 in Journal of Physics D: Applied Physics
1D all-inorganic perovskites microwires horizontally aligned on mica show great potential in high performance optical and optoelectronic devices. In spite of the tremendous progress in their growth and properties studies, the growth mechanism for epitaxy of perovskites microwires on mica has not been well understood. Herein, we present a home-built in situ growth monitoring system to study the growth mechanism of the CsPbBr 3 microwires on mica with the physical vapor deposition (PVD). Through in situ monitoring the growth of the CsPbBr 3 microwires, the detailed growth behavior can be directly investigated. It is found that the length growth rate of the microwires may be enhanced with the large undercooling (the temperature difference between the precursor and the deposition substrate), which provides the possibility to achieve the rapid growth of the wires. Additionally, CsPbBr 3 microwires with smaller diameter show the higher growth rate than that with larger diameter, which is consistent with the theoretical analysis based on the adatom diffusion. By increasing the undercooling, CsPbBr 3 microwires with the length up to 200 μ m can be grown in 15 s, which is more efficient than the traditional vapor growth routes. Furthermore, the photoluminescence and high performance of the photodetector device based on these CsPbBr 3 wire arrays indicate that the as-grown CsPbBr 3 wires have the potential in the optical and optoelectronic device applications.