Polyvinyl chloride (PVC), owing to its excellent electrical properties and low cost, is widely applied in the inner insulation and outer sheath of cables. To achieve early fault warning based on characteristic gases, this study integrates experimental testing with molecular simulations to systematically reveal the decomposition and gas generation characteristics of different PVC layers under electrical and thermal stresses. The results indicate that inner-layer PVC under electrical stress predominantly generates small-molecule olefins and halogenated hydrocarbons, while outer-layer PVC during thermal decomposition mainly produces hydrogen chloride, alkanes, and fragments of plasticizers. The surrounding atmosphere significantly regulates the gas generation pathways: air promotes the formation of CO2 and H2O, whereas electrical discharges accelerate the release of unsaturated hydrocarbons such as acetylene. By employing TG-FTIR, ReaxFF molecular dynamics, and DFT spectral calculations, a normalized infrared spectral library covering typical products was established and combined with the non-negative least squares method to realize quantitative deconvolution of mixed gases. Ultimately, a diagnostic system was constructed based on the concentration ratios of characteristic gases, which can effectively distinguish the failure modes of inner and outer PVC layers as well as different stress types. This provides a feasible approach for early detection of cable faults and supports intelligent maintenance strategies.
Due to their compact structure and low laying cost, three-core power cables are widely used for power distribution networks. The three-phases of such cables are distributed symmetrically with a 120° shift to each other. Phase current is an important parameter to reflect the operation state of the power system and three-core cable. Three-core symmetrical power cables use a common shield, leading to magnetic field cancelation outside the cable during steady operation. Thus, traditional magnetic-based current transformers cannot measure the phase current on three-core cable non-invasively. In order to measure the phase current more conveniently, a phase current measurement method for three-core cables based on a magnetic sensor is proposed in this paper. Nonlinear equations of a phase current and the magnetic field of a measuring point are constructed. The calculated magnetic field distribution of the three-core cable is verified using a finite element simulation. The effectiveness of the measurement method is further validated through experiments. This proposed method is able to conveniently detect the phase current of three-core power cables, which can help cable maintenance.
High-voltage cables are the main arteries of urban power supply. Cable accessories are connecting components between different sections of cables or between cables and other electrical equipment. The stress in the cold shrink tube of cable accessories is a key parameter to ensure the stable operation of the power system. This paper attempts to explore a method for measuring the stress in the cold shrink tube of high-voltage cable accessories based on ultrasonic longitudinal wave attenuation. Firstly, a pulse ultrasonic longitudinal wave testing system based on FPGA is designed, where the ultrasonic sensor operates in a single-transmit, single-receive mode with a frequency of 3 MHz, a repetition frequency of 50 Hz, and a data acquisition and transmission frequency of 40 MHz. Then, through experiments and theoretical calculations, the transmission and attenuation characteristics of ultrasonic longitudinal waves in multi-layer elastic media are studied, revealing an exponential relationship between ultrasonic wave attenuation and the thickness of the cold shrink tube. Finally, by establishing a theoretical model of the radial stress of the cold shrink tube, using the thickness of the cold shrink tube as an intermediate variable, an effective measurement of the stress of the cold shrink tube was achieved.
Ceramic outdoor insulators play an important role in electrical insulation and mechanical support because of good chemical and thermal stability, which have been widely used in power systems. However, the brittleness and surface discharge of ceramic material greatly limit the application of ceramic insulators. From the perspective of sintering technology, flash sintering technology is used to improve the performance of ceramic insulators. In this paper, the simulation model of producing the ceramic insulator by the flash sintering technology was set up. Material Studio was used to study the influence of electric field intensity and temperature on the alumina unit cell. COMSOL was used to study the influence of electric field intensity and current density on sintering speed, density and grain size. Obtained results showed that under high temperature and high voltage, the volume of the unit cell becomes smaller and the atoms are arranged more closely. The increase of current density can result in higher ceramic density and larger grain size. With the electric field intensity increasing, incubation time shows a decreasing tendency and energy consumption is reduced. Ceramic insulators with a higher uniform structure and a smaller grain size can show better dielectric performance and higher flashover voltage.
The water-blocking buffer layer of high-voltage cross-linked polyethylene (XLPE) power cables is prone to degradation during long-term operation due to factors such as moisture and ablation. The degradation may cause an increase in leakage current, which is affected by frequency. However, the correlation between buffer layer status and leakage current under various frequencies needs further investigation. Accordingly, this paper investigates leakage current characteristics of cable water-blocking buffer layers with different statuses under multi-frequency excitation. Firstly, a multi-frequency leakage current test platform was established. Afterwards, composite specimens consisting of XLPE insulation and a water-blocking buffer layer were prepared in four different states: normal, moisture-affected, slightly ablated, and severely ablated. The leakage current responses of different specimens under various voltage frequencies were systematically examined. The results show that, under moisture-affected conditions, the leakage current increases by 15–30% compared with the normal state. The voltage–current phase difference decreases significantly in the low-frequency range by 9–64°. The total harmonic content increases markedly as the frequency decreases, with the 3rd, 5th, and 7th harmonics exhibiting the highest sensitivity. Ablated samples have limited influence on the leakage current. But localized spikes appear in the waveform. Under normal conditions, the leakage current waveform follows the applied sinusoidal voltage, forming a natural symmetry in both frequency and time domains. However, moisture ingress and ablation defects break this symmetry by introducing harmonic distortion in the frequency domain and pulse-shaped spikes in the time domain, respectively. The method utilizes low-frequency leakage-current harmonics and harmonic–residual spikes to identify buffer layer moisture and ablation defects. The proposed method enables the effective identification of different buffer layer states and provides a technical approach for the defect diagnosis of water-blocking buffer layers in high-voltage cables.