This publication presents research work which contains the optimum parameters of the agri-biomass: maize and oat straws torrefaction process. Parameters which are the most important for the torrefaction process and its products are temperature and residence time. Thermogravimetric analysis was performed as well as the torrefaction process using an electrical furnace on a laboratory scale at a temperature between 250–525 °C. These biomass torrefaction process parameters—residence time and temperature—were necessary to perform the design and construction of semi-pilot scale biomass torrefaction installations with a regimental dryer and a woody and agri-biomass regimental torrefaction reactor to perform a continuous torrefaction process using superheated steam. In the design installation the authors also focused on biochar, a bi-product of biofuel which will be used as an additive for natural bio-fertilizers. Kinetic analysis of torrefaction process using maize and oat straws was performed using NETZSCH Neo Kinetics software. It was found that kinetic analysis methods conducted with multiple heating rate experiments were much more efficient than the use of a single heating rate. The best representations of the experimental data for the straw from maize straw were found for the n-order reaction model. A thermogravimetric analysis, TG-MS analysis and VOC analysis combined with electrical furnace installation were performed on the maize and oat straw torrefaction process. The new approach in the work presented is different from that of current scientific achievements due to the fact that until now researchers have worked on performing processes on oat and maize straws by means of the torrefaction process for the production of a biochar as an additive for natural bio-fertilizers. None of them looked for economically reasonable mass loss ratios. In this work the authors made the assumption that a mass loss in the area of 45–50% is the most reasonable loss for the two mentioned agri-biomass processes. On this basis, a semi-pilot installation could be produced in a further BIOCARBON project step. The kinetic parameters which were calculated will be used to estimate the size of the apparatuses, the biomass dryer, and biomass torrefaction reactor.

Due to its adverse impact on health, as well as its global distribution, long atmospheric lifetime and propensity for deposition in the aquatic environment and in living tissue, the US Environmental Protection Agency (US EPA) has classified mercury and its compounds as a severe air quality threat. Such widespread presence of mercury in the environment originates from both natural and anthropogenic sources. Global anthropogenic emission of mercury is evaluated at 2000 Mg year⁻¹. According to the National Centre for Emissions Management (Pol. KOBiZE) report for 2014, Polish annual mercury emissions amount to approximately 10 Mg. Over 90% of mercury emissions in Poland originate from combustion of coal. The purpose of this paper was to understand mercury behaviour during sub-bituminous coal and lignite combustion for flue gas purification in terms of reduction of emissions by active methods. The average mercury content in Polish sub-bituminous coal and lignite was 103.7 and 443.5 μg kg⁻¹. The concentration of mercury in flue gases emitted into the atmosphere was 5.3 μg m⁻³ for sub-bituminous coal and 17.5 μg m⁻³ for lignite. The study analysed six low-cost sorbents with the average achieved efficiency of mercury removal from 30.6 to 92.9% for sub-bituminous coal and 22.8 to 80.3% for lignite combustion. Also, the effect of coke dust grain size was examined for mercury sorptive properties. The fine fraction of coke dust (CD) adsorbed within 243–277 μg Hg kg⁻¹, while the largest fraction at only 95 μg Hg kg⁻¹. The CD fraction < 0.063 mm removed almost 92% of mercury during coal combustion, so the concentration of mercury in flue gas decreased from 5.3 to 0.4 μg Hg m⁻³. The same fraction of CD had removed 93% of mercury from lignite flue gas by reducing the concentration of mercury in the flow from 17.6 to 1.2 μg Hg m⁻³. The publication also presents the impact of photochemical oxidation of mercury on the effectiveness of Hg vapour removal during combustion of lignite. After physical oxidation of Hg in the flue gas, its effectiveness has increased twofold.

This work presents the results of research on the thermo-chemical conversion of woody biomass–pine wood coming from lodzkie voivodship forests and sewage sludge from the Group Sewage Treatment Plant of the Łódź Urban Agglomeration. Laboratory scale analyses of the carbonization process were carried out, initially using the TGA technique (to assess activation energy (EA)), followed by a flow reactor operating at temperature levels of 280–525 °C. Both the parameters of carbonized solid biofuel and biochar as a carrier for fertilizer (proximate and ultimate analysis) and the quality of the torgas (VOC) were analyzed. Analysis of the pine wood and sewage sludge torrefaction process shows clearly that the optimum process temperature would be around 325–350 °C from a mass loss ratio and economical perspective. This paper shows clearly that woody biomass, such as pine wood and sewage sludge, is a very interesting material both for biofuel production and in further processing for biochar production, used not only as an energy carrier but also as a new type of carbon source in fertilizer mixtures.

One of the solid waste produced during the combustion of coal are fly ashes. Disposal challenges and environmental consequences are the results of significant process yield and atmospheric emission of fly ashes. The exact chemical composition of FA depends mainly on the type of utilised fuel and combustion conditions. It consists mainly of chemically stable metal oxides, such as Al₂O₃, Fe₂O₃, SiO₂, CaO, MgO, K₂O, Na₂O and TiO₂, but its toxicity is related to the possible presence of some trace elements, such as As, Hg, Cd, Se and Cr. The chemical and physical properties of fly ash (e.g., particle size distribution, porosity, and surface area) make it suitable as an adsorbent to remove various impurities from process flows such as flue gas stream. Its suitability for capturing mercury from flue gas was experimentally confirmed due to its abundant supply, particle size, bulk density, porosity, chemical composition and low cost. Hence, the use of fly ash as adsorbents and precursors for the production of heavy metal adsorbents is of great practical importance, as it reduces the cost of mercury capture and alleviates the problems associated with the disposal of solid waste. Studies showed that the chemical components present in fly ash additives could stimulate catalytic oxidative capacity, which increases the adsorption of Hg⁰ oxidation and adsorption of both Hg and CO₂. The presented study analysed fly ashes from different zones of the electrostatic precipitator and verified their suitability for removing impurities from flue gases, i.e., mercury and carbon dioxide. The results outlined modified fly ash as having good Hg and CO₂ removal capabilities. The adsorption efficiency of Hg reached 92% for Hg and 66% for CO₂, while untreated fly ash reached 67% for Hg and 59% for CO₂.

The research presented by the authors in this paper focused on understanding the behavior of mercury during coal combustion and flue gas purification operations. The goal was to determine the flue gas temperature on the mercury emissions limits for the combustion of lignites in the energy sector. The authors examined the process of sorption of mercury from flue gases using fine-grained organic materials. The main objectives of this study were to recommend a low-cost organic adsorbent such as coke dust (CD), corn straw char (CS-400), brominated corn straw char (CS-400-Br), rubber char (RC-600) or granulated rubber char (GRC-600) to efficiently substitute expensive dust-sized activated carbon. The study covered combustion of lignite from a Polish field. The experiment was conducted at temperatures reflecting conditions inside a flue gas purification installation. One of the tested sorbents—tire-derived rubber char that was obtained by pyrolysis—exhibited good potential for Hg⁰ into Hg²⁺ oxidation, resulting in enhanced mercury removal from the flue. The char characterization increased elevated bromine content (mercury oxidizing agent) in comparison to the other selected adsorbents. This paper presents the results of laboratory tests of mercury sorption from the flue gases at temperatures of 95, 125, 155 and 185 °C. The average mercury content in Polish lignite was 465 μg·kg⁻¹. The concentration of mercury in flue gases emitted into the atmosphere was 17.8 µg·m⁻³. The study analyzed five low-cost sorbents with the average achieved efficiency of mercury removal from 18.3% to 96.1% for lignite combustion depending on the flue gas temperature.

In this paper authors present research results which are the optimum parameters of the torrefaction process using straw from oats and maize. The most important parameters for the torrefaction process are temperature and residence time. Both parameters are essential to designing and construction of industrial biomass torrefaction installations. Energy crops and waste coming from agricultural production have the most promising perspective from all kind of renewable energy sources in Poland. Currently, intensive studies on the process of biomass torrefaction are being carried out. In this experimental investigation, authors examined the torrefaction process of two types of agriculture biomass, such as: oats, maize. The main overarching objective of the experimental studies described below is the development of various biochar as an additive to agricultural fertilizers resulting from the conversion of biomass from agriculture residues – straw from oats and maize. The last of enumerated biomasses is treated through different conversion processes such as: drying, torrefaction to homogenize their physical and chemical properties. Among many of its areas, it is extremely important to optimize the production of biomass energy plants and its refinement (in the torrefaction process), which will improve the balance and profitability of energy production from RES, and reduce the logistics and storage costs of this fuel and improve the efficiency of biomass combustion process. When implementing new technologies indicated in this work and optimizing the harvesting of plant biomass, the negative impact on the environment caused by stored municipal waste can be reduced. This biomass torrefaction process temperature and residence time were necessary for the design and construction of semi-pilot scale biomass torrefaction installations with dryer and torrefaction reactor to perform a continuous biomass torrefaction process using superheated steam