Concrete is an economical and efficient material for attenuating radiation. The potential of concrete in attenuating radiation is attributed to its density, which in turn depends on the mix design of concrete. This paper presents the findings of a study conducted to evaluate the radiation attenuation with varying water-cement ratio (w/c), thickness, density, and compressive strength of concrete. Three different types of concrete, i.e., normal concrete, barite, and magnetite containing concrete, were prepared to investigate this study. The radiation attenuation was calculated by studying the dose absorbed by the concrete and the linear attenuation coefficient. Additionally, artificial neural network (ANN) and gene expression programming (GEP) models were developed for predicting the radiation shielding capacity of concrete. A correlation coefficient (R), mean absolute error (MAE), and root mean square error (RMSE) were calculated as 0.999, 1.474 mGy, 2.154 mGy and 0.994, 5.07 mGy, 5.772 mGy for the training and validation sets of the ANN model, respectively. Similarly, for the GEP model, these values were recorded as 0.981, 13.17 mGy, and 20.20 mGy for the training set, whereas the validation data yielded R = 0.985, MAE = 12.2 mGy, and RMSE = 14.96 mGy. The statistical evaluation reflects that the developed models manifested close agreement between experimental and predicted results. In comparison, the ANN model surpassed the accuracy of the GEP models, yielding the highest R and the lowest MAE and RMSE. The parametric and sensitivity analysis revealed the thickness and density of concrete as the most influential parameters in contributing towards radiation shielding. The mathematical equation derived from the GEP models signifies its importance such that the equation can be easily used for future prediction of radiation shielding of high-density concrete.

Steel fibers are widely extracted from scrap tyres, causing environmental concerns. This paper presents the use of steel fibers in variable proportions extracted from scrap tyres. The enhancement of the confinement was envisaged through the addition of steel fibers obtained from scrap tyres. The study included an experimental program for the development of constitutive material models for ordinary Portland cement (OPC) concrete and concrete with added steel fibers. A mix design was carried out for OPC, targeting a compressive strength of 3000 psi. Steel fibers were added to OPC in ratios of 1.0% to 3.0%, with an increment of 0.5%. Concrete columns, with cross-sectional dimensions of 6 × 6 inches and a length of 30 inches, were cast with both OPC and fiber-reinforced concrete. The column confinement was evaluated with a different spacing of ties (3- and 4-inch center-to-center). Compression tests on the concrete columns indicate that the addition of steel fibers to a concrete matrix results in an appreciable increase in strength and ductility. Overall, increasing the percentage of steel fibers increased the compression strength and the ductility of concrete. The maximum strain in the concrete containing 2.5% steel fibers increased by 285% as compared to the concrete containing 1% of steel fibers. An optimum percentage of 2.5% steel fibers added to the concrete resulted in a 39% increase in compressive strength, accompanied by a significant improvement in ductility. The optimum content of steel fibers, when used in confined columns, showed that confined compression strength increased with the addition of steel fibers. However, it is recommended that additional columns on the basis of the optimum steel fiber content shall be tested to evaluate their effectiveness in reducing the stirrup spacing.

In this study, Multiwalled Carbon Nanotubes (MWCNTs) and Marble Powder (MP) have been utilized in reinforced concrete columns to assess their structural behavior. The nanotubes from 0.025% to 0.20% and 5% MP by weight of cement were used. The compressive strength of reinforced concrete columns and cubes was analyzed as the main property. The incorporation of MWCNTs and marble powder was able to increase the compressive strength of columns by 72.69% and mortar by 42.45% as compared to reference concrete. The ductility was noted to be improved by 42.04%. The load-deformation and stress-strain behaviors were also analyzed. The Scanning Electron Microscopy (SEM) analysis revealed the formation of a strong compact bridge (90–100 layers), Calcium Silicate Hydrate (C-S-H) gel, evenly dispersion, and bridging effect caused by MWCNTs. The incorporation of 0.20% MWCNTs by weight of cement was recommended to be effectively used as a reinforcing agent in concrete.

This study aimed to determine how radiation attenuation would change when the thickness, density, and compressive strength of clay bricks, modified with partial replacement of clay by fly ash, iron slag, and wood ash. To conduct this investigation, four distinct types of bricks—normal, fly ash-, iron slag-, and wood ash-incorporated bricks were prepared by replacing clay content with their variable percentages. Additionally, models for predicting the radiation-shielding ability of bricks were created using gene expression programming (GEP) and artificial neural networks (ANN). The addition of iron slag improved the density and compressive strength of bricks, thus increasing shielding capability against gamma radiation. In contrast, fly ash and wood ash decreased the density and compressive strength of burnt clay bricks, leading to low radiation shielding capability. Concerning the performance of the Artificial Intelligence models, the root mean square error (RMSE) was determined as 0.1166 and 0.1876 nC for the training and validation data of ANN, respectively. The training set values for the GEP model manifested an RMSE equal to 0.2949 nC, whereas the validation data produced RMSE = 0.3507 nC. According to the statistical analysis, the generated models showed strong concordance between experimental and projected findings. The ANN model, in contrast, outperformed the GEP model in terms of accuracy, producing the lowest values of RMSE. Moreover, the variables contributing towards shielding characteristics of bricks were studied using parametric and sensitivity analyses, which showed that the thickness and density of bricks are the most influential parameters. In addition, the mathematical equation generated from the GEP model denotes its significance such that it can be used to estimate the radiation shielding of burnt clay bricks in the future with ease.