The issue of brittleness and low post-peak load energy associated with the plain HSC led to the development of fiber-reinforced concrete (FRC) by using discrete fiber filaments in the plain matrix. Due to the high environmental impact of industrial fibers and plasticizers, FRC development is ecologically challenged. Sustainability issues demand the application of eco-friendly development of FRC. This study is aimed at the evaluation of coir as a fiber-reinforcement material in HSC, with the incorporation of silica fume as a partial replacement of cement. For this purpose, a total of 12 concrete mixes were produced by using three different doses of coir (0%, 1%, 1.5%, and 2% by wt. of binder) with silica fume (0%, 5%, and 10% as volumetric replacements of cement). The examined parameters include compressive strength, shear strength, splitting tensile strength, ultrasonic pulse velocity, water absorption, and chloride ion permeability. The scanning electron microscopy (SEM) technique was adopted to observe the microstructure of the CF-reinforced concrete. The results revealed that due to the CF addition, the compressive strength of HSC reduces notably; however, the splitting tensile strength and shear strength experienced notable improvements. At the combined incorporation of 1.5% CF with 5% silica fume, the splitting tensile strength and shear strength of the concrete experienced improvements of 47% and 70%, respectively, compared to that of the control mix. The CF incorporation is detrimental to the imperviousness of concrete. The combined incorporation of CF and silica fume is recommended to minimize the negative effects of CF on the permeability resistance of concrete. The SEM results revealed that CF underwent a minor shrinkage with the age.

Climate change has become trending news due to its serious impacts on Earth. Initiatives are being taken to lessen the impact of climate change and mitigate it. Among the different initiatives, researchers are aiming to find suitable alternatives for cement. This study is a humble effort to effectively utilize industrial- and agricultural-waste-based pozzolanic materials in concrete to make it economical and environmentally friendly. For this purpose, a ternary blend of binders (i.e., cement, fly ash, and rice husk ash) was employed in concrete. Different variables such as the quantity of different binders, fine and coarse aggregates, water, superplasticizer, and the age of the samples were considered to study their influence on the compressive strength of the ternary blended concrete using gene expression programming (GEP) and artificial neural networking (ANN). The performance of these two models was evaluated using R², RMSE, and a comparison of regression slopes. It was observed that the GEP model with 100 chromosomes, a head size of 10, and five genes resulted in an optimum GEP model, as apparent from its high R² value of 0.80 and 0.70 in the TR and TS phase, respectively. However, the ANN model performed better than the GEP model, as evident from its higher R² value of 0.94 and 0.88 in the TR and TS phase, respectively. Similarly, lower values of RMSE and MAE were observed for the ANN model in comparison to the GEP model. The regression slope analysis revealed that the predicted values obtained from the ANN model were in good agreement with the experimental values, as shown by its higher R² value (0.89) compared with that of the GEP model (R² = 0.80). Subsequently, parametric analysis of the ANN model revealed that the addition of pozzolanic materials enhanced the compressive strength of the ternary blended concrete samples. Additionally, we observed that the compressive strength of the ternary blended concrete samples increased rapidly within the first 28 days of casting.

Concrete is an economical and efficient material for attenuating radiation. The potential of concrete in attenuating radiation is attributed to its density, which in turn depends on the mix design of concrete. This paper presents the findings of a study conducted to evaluate the radiation attenuation with varying water-cement ratio (w/c), thickness, density, and compressive strength of concrete. Three different types of concrete, i.e., normal concrete, barite, and magnetite containing concrete, were prepared to investigate this study. The radiation attenuation was calculated by studying the dose absorbed by the concrete and the linear attenuation coefficient. Additionally, artificial neural network (ANN) and gene expression programming (GEP) models were developed for predicting the radiation shielding capacity of concrete. A correlation coefficient (R), mean absolute error (MAE), and root mean square error (RMSE) were calculated as 0.999, 1.474 mGy, 2.154 mGy and 0.994, 5.07 mGy, 5.772 mGy for the training and validation sets of the ANN model, respectively. Similarly, for the GEP model, these values were recorded as 0.981, 13.17 mGy, and 20.20 mGy for the training set, whereas the validation data yielded R = 0.985, MAE = 12.2 mGy, and RMSE = 14.96 mGy. The statistical evaluation reflects that the developed models manifested close agreement between experimental and predicted results. In comparison, the ANN model surpassed the accuracy of the GEP models, yielding the highest R and the lowest MAE and RMSE. The parametric and sensitivity analysis revealed the thickness and density of concrete as the most influential parameters in contributing towards radiation shielding. The mathematical equation derived from the GEP models signifies its importance such that the equation can be easily used for future prediction of radiation shielding of high-density concrete.

Reinforced concrete structures are subjected to frequent maintenance and repairs due to steel reinforcement corrosion. Fiber-reinforced polymer (FRP) laminates are widely used for retrofitting beams, columns, joints, and slabs. This study investigated the non-linear capability of artificial intelligence (AI)-based gene expression programming (GEP) modelling to develop a mathematical relationship for estimating the interfacial bond strength (IBS) of FRP laminates on a concrete prism with grooves. The model was based on five input parameters, namely axial stiffness (E_ft_f), width of FRP plate (b_f), concrete compressive strength (f_c′), width of groove (b_g), and depth of the groove (h_g), and IBS was considered the target variable. Ten trials were conducted based on varying genetic parameters, namely the number of chromosomes, head size, and number of genes. The performance of the models was evaluated using the correlation coefficient (R), mean absolute error (MAE), and root mean square error (RMSE). The genetic variation revealed that optimum performance was obtained for 30 chromosomes, 11 head sizes, and 4 genes. The values of R, MAE, and RMSE were observed as 0.967, 0.782 kN, and 1.049 kN for training and 0.961, 1.027 kN, and 1.354 kN. The developed model reflected close agreement between experimental and predicted results. This implies that the developed mathematical equation was reliable in estimating IBS based on the available properties of FRPs. The sensitivity and parametric analysis showed that the axial stiffness and width of FRP are the most influential parameters in contributing to IBS.

Steel fibers are widely extracted from scrap tyres, causing environmental concerns. This paper presents the use of steel fibers in variable proportions extracted from scrap tyres. The enhancement of the confinement was envisaged through the addition of steel fibers obtained from scrap tyres. The study included an experimental program for the development of constitutive material models for ordinary Portland cement (OPC) concrete and concrete with added steel fibers. A mix design was carried out for OPC, targeting a compressive strength of 3000 psi. Steel fibers were added to OPC in ratios of 1.0% to 3.0%, with an increment of 0.5%. Concrete columns, with cross-sectional dimensions of 6 × 6 inches and a length of 30 inches, were cast with both OPC and fiber-reinforced concrete. The column confinement was evaluated with a different spacing of ties (3- and 4-inch center-to-center). Compression tests on the concrete columns indicate that the addition of steel fibers to a concrete matrix results in an appreciable increase in strength and ductility. Overall, increasing the percentage of steel fibers increased the compression strength and the ductility of concrete. The maximum strain in the concrete containing 2.5% steel fibers increased by 285% as compared to the concrete containing 1% of steel fibers. An optimum percentage of 2.5% steel fibers added to the concrete resulted in a 39% increase in compressive strength, accompanied by a significant improvement in ductility. The optimum content of steel fibers, when used in confined columns, showed that confined compression strength increased with the addition of steel fibers. However, it is recommended that additional columns on the basis of the optimum steel fiber content shall be tested to evaluate their effectiveness in reducing the stirrup spacing.