Artur Dylong

Dr. Artur Dylong

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 December 2021 in Energies
Verified
Journal Article
Open access
PDF file
Anna ManowskaAnna Manowska
Anna Manowska
Aurelia RybakAurelia Rybak
Aurelia Rybak
ADArtur Dylong
Artur Dylong
JPJoachim Pielot
Joachim Pielot
Natural gas is one of the main energy sources in Poland and accounts for about 15% of the primary energy consumed in the country. Poland covers only 1/5 of its demand from domestic deposits. The rest is imported from Russia, Germany, Norway, the Czech Republic, Ukraine, and Central Asia. An important issue concerning the market of energy resources is the question of the direct impact of the prices of energy resources on the income of exporting and importing countries. It should also be remembered that unexpected and large fluctuations are detrimental to both exporters and importers of primary fuels. The article analyzes natural gas deposits in Poland, raw material trade and proposes a model for forecasting the volume of its consumption, which takes into account historical consumption, prices of energy resources and assumptions of Poland’s energy policy until 2040. A hybrid model was built by combining ARIMA with LSTM artificial neural networks. The validity of the constructed model was assessed using ME, MAE, RMSE and MSE. The average percentage error is 2%, which means that the model largely represents the real gas consumption course. The obtained forecasts indicate an increase in consumption by 2040.

22 December 2023 in Energies
Verified
Journal Article
Open access
PDF file
Anna ManowskaAnna Manowska
Anna Manowska
ADArtur Dylong
Artur Dylong
BTBogdan Tkaczyk
Bogdan Tkaczyk
JMJarosław Manowski
Jarosław Manowski
This article explores the efficiency of photovoltaic (PV) panels, which is crucial in the search for sustainable energy solutions. The study presents a comprehensive analysis of the maximum solar potential achievable through photovoltaic technologies amidst the increasing global energy demands. The research examines solar radiation measurement techniques, the incidence angle of solar rays, and the intricacies of PV panel efficiency. It highlights the potential for improving the performance of solar-based energy systems. Four main sections are covered, beginning with an introduction to the importance of energy storage in sustainable energy production, especially in the context of the European Union’s energy goals and the Green Deal. The following sections discuss the precision needed in the geographical positioning of measurement systems, the impact of light physics, and variable weather conditions on energy capture. The last section presents a novel clock algorithm regulation system designed to enhance the efficiency of the measurement system.

20 December 2021 in Energies
Verified
Journal Article
Open access
PDF file
JJJarosław Joostberens
Jarosław Joostberens
Aurelia RybakAurelia Rybak
Aurelia Rybak
JPJoachim Pielot
Joachim Pielot
ADArtur Dylong
Artur Dylong
The flow rate of solids is subject to random disturbances of the changing feed and can significantly affect the quantitative and qualitative parameters of the coal flotation products. This quantity can be described as a stochastic process. The paper presents the results of the solids flow rate model for coal flotation identification calculations, treated as a disturbance to the process. This is an innovative approach to modelling those quantitative parameters of the flotation feed that are measurably available and whose random changes have a significant impact on the enhancement process under industrial conditions. These include the volumetric flow rate of the feed and, in particular, concentration of solids in the feed. Therefore, it is suggested that random changes of these two parameters of the feed should be mapped using a model of one quantity—the flow rate of solids. This solution is advantageous because this quantity, as a quantitative parameter of the feed, has a significant impact on the course of the coal flotation process. The model is necessary in the process of designing an automatic control system through simulation tests. It allows us to generate a data string simulating random changes to this quantitative parameter of the feed. On this basis, in the simulation model, the correct functioning of the automatic control system is tested, the task of which is to compensate the influence of this disturbance. To determine the empirical model of the feed solids flow rate, measurement data obtained during the registration of the solids concentration and volumetric flow rate of the feed were used in four consecutive periods of operation of an industrial facility of one of the Polish coal processing plants. The time courses of the solids flow rate in the feed were described by ARMA (autoregressive–moving-average model) means, and the two-stage least squares method was used to estimate the model parameters. The results of the identification and verification of the designated model showed the correctness of adopting the third-order ARMA model, with parameters a1 = −1.0682, a2 = −0.2931, a3 = 0.3807, c1 = −0.1588, c2 = −0.2301, c3 = 0.1037, and variance σ2ε = 0.0891, white noise sequence εt, determined on the basis of a series of residuals described by the fifth-order model. It has been shown that the identified model of the flow rate of solids of the feed to flotation as disturbances can be used to develop a predictive model that allows forecasting the modelled quantity with a prediction horizon equal to the sampling period. One-step forecasting based on the determined predictor equation was found to give results consistent with the recorded values of the solid part flow rate of the feed and the extreme values of the prediction error are within the range from −1.08 to 2.90 kg/s.

23 February 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SBSławomir Bartoszek
Sławomir Bartoszek
GĆGrzegorz Ćwikła
Grzegorz Ćwikła
GKGabriel Kost
Gabriel Kost
ADArtur Dylong
Artur Dylong
Dominik BałagaDominik Bałaga
Dominik Bałaga
SJSebastian Jendrysik
Sebastian Jendrysik
This paper presents a sensitivity analysis of positioning accuracy in a localization system based on signal time-of-flight measurements, intended for operation in underground roadway workings. The underground environment is characterized by limited installation space, numerous obstacles causing multipath propagation, and the presence of sections with non-uniform geometry, which in practice leads to a “flattening” of the transmitter constellation and a deterioration of the conditioning of the trilateration problem. As a result, even small changes in input parameters (e.g., related to infrastructure geometry, distance-measurement quality, or the adopted model) may cause a significant change in the position-estimation error, thereby reducing the reliability of roadheader localization across the entire working area. In this study, a local sensitivity analysis is employed to identify the parameters that dominate the positioning outcome. Sensitivity coefficients are defined in a normalized form and are determined numerically using a perturbation approach (changing a given input parameter by a prescribed percentage), which avoids analytical differentiation of the complex relationships arising from the trilateration equations. The analysis is performed for a roadway scenario supported by an ŁP10 steel arch yielding support, with transmitters installed under the support arch and the roadheader trajectory represented by a sequence of consecutive position vectors. The obtained results allow the solution’s susceptibility to errors and uncertainties in the parameters to be assessed and indicate which parameters require priority control in practical implementation. On this basis, recommendations are formulated for the design and maintenance of the localization infrastructure, including transmitter placement and reconfiguration rules (relocation or adding an additional transmitter), to maintain stable positioning quality under operational mining conditions.