This research examines the possibilities of regulating the structure of cellulose precursor fibers spun from solutions in N-methylmorpholine-N-oxide when replacing aqueous coagulation baths with thermodynamically softer alcohol baths at different temperatures. The fibers were spun by the dry jet–wet method in isobutanol coagulation baths with a temperature of 25 °C and 70 °C. The study of the phase state of the solvent–coagulant system using viscometry and point cloud methods revealed the temperature-concentration regions of the single-phase and two-phase states of the system. Using elemental analysis, DSC (differential scanning calorimetry) and XRD (X-ray diffraction) methods, it was shown that just spun fibers, due to the presence of a residual amount of solvent and coagulant in them, regardless of the temperature of the precipitator, have an amorphous structure. Additional washing with water completely washed away the solvent and coagulant as well, however, the structure of cellulose changes slightly, turning into a defective amorphous-crystalline one. A relationship was found between the phase composition, structure, and properties of just spun fibers and precursors washed with water. Thus, the loss of structural ordering of both just spun and washed cellulose fibers leads to a decrease in strength characteristics and an increase in deformation. The thermal behavior of the fibers is determined by their phase composition. Fibers just spun into hot alcohol containing a coagulant and traces of solvent acquire thermal stability up to 330 °C. During the pyrolysis of the obtained precursors up to 1000 °C, the value of the carbon yield doubles. The amorphized structure of the obtained fibers allows us to consider it as a model when analyzing the transformation of the structure of precursors during thermolysis.
In this study, the interaction between poly(styrene sulfonic acid), polyacrylic acid, poly(meth-acrylic acid), poly(L-glutamic acid), poly(vinyl sulfate), and ternary copolymer of styrene with maleic anhydride and methacrylic acid (3: 2: 1), as well as DNA with lipid vesicles composed of zwitterion (electroneutral) lipid phosphatidylcholine, has been investigated. The methods of centrifuge ultrafiltration and dynamic light scattering reveal that, at pH 4.2, all polyacids under study are effectively adsorbed on the phospholipid membrane. The polymer-membrane complex is stabilized by hydrogen bonds and hydrophobic interactions in addition to electrostatic bonds. Even though, to a greater or lesser extent, all polyacids are capable of undergoing adsorption on the membrane in a slightly acidic medium, their effect on the membrane permeability is substantially different and is correlated with the ability of a polymer to form multiple interactions with phospholipid molecules. Poly(acrylic acid), poly(methacrylic acid), poly(styrene sulfonic acid), and the ternary copolymer of styrene with maleic anhydride and methacrylic acid can produce the membrane pores that are permeable to low-molecular-mass compounds. At the same time, poly(L-glutamic acid), poly(vinyl sulfate), and DNA exert no effect on the membrane permeability, although they are sorbed on the membrane surface.
Positively charged polyelectrolytes hold significant potential as materials for creating antibacterial coatings. We examined the physicochemical and mechanical properties of the macromolecules in water solutions and in coatings for the series of branched polyethyleneimine (PEI) and linear polydiallyldimethylammonium chloride (PDADMAC) with different molecular weights. The microbiological study was conducted to analyze the biocidal activity of the polycation solutions and coatings towards foodborne bacteria. While the moisture saturation of the polycationic coatings and biocidal activity did not significantly depend on the chemical nature of charged groups or the molecular weight or architecture of macromolecules, the lowering of the molecular weight of polymers resulted in the loss of cohesive forces in the coatings and to a dramatic loss of stability when being washed off with water. The diffusion coefficient (D0) of macromolecules was identified as a key parameter for the wash-off mechanism. Films formed by molecules with a D0 below 1 × 10−7 cm2/s demonstrated a high resistance to wash-off procedures. We demonstrated that PEI and PDADMAC samples with high molecular weights showed high antimicrobial activity towards L. monocytogenes. Our results highlight the importance of macromolecule characteristics in the development of new biocidal coatings based on polycations.
A facile technique for the preparation of mixed polylactide micelles from amorphous poly-D,L-lactide-block-polyethyleneglycol and crystalline amino-terminated poly-L-lactide is described. In comparison to the classical routine solvent substitution method, the ultrasonication assisted formation of polymer micelles allows shortening of the preparation time from several days to 15–20 min. The structure and morphology of mixed micelles were analyzed with the assistance of electron microscopy, dynamic and static light scattering and differential scanning calorimetery. The resulting polymer micelles have a hydrodynamic radius of about 150 nm and a narrow size distribution. The average molecular weight of micelles was found to be 2.1 × 107 and the aggregation number was calculated to be 6000. The obtained biocompatible particles were shown to possess low cytotoxicity, high colloid stability and high stability towards enzymatic hydrolysis. The possible application of mixed polylactide micelles as drug delivery vehicles was studied for the antitumor hydrophobic drug paclitaxel. The lethal concentration (LC50) of paclitaxel encapsulated in polylactide micelles was found to be 42 ± 4 µg/mL—a value equal to the LC50 of paclitaxel in the commercial drug Paclitaxel-Teva.
1 May 2019 in Russian Journal of General Chemistry
Thin conductive films have been obtained via dehydration and reduction of composite films based on polyvinyl alcohol and graphene oxide. Composition and structure of the nanocomposites as well as the...