This study presents an efficient control technique for computing the optimum space-vector voltage in power converters. The presented optimized direct power control (ODPC) provides a closed-form formula for the converter space-vector voltage, which, based on Lagrange operators for the optimum trajectory, provides the commanded complex apparent power. The voltage required by the ODPC is obtained with a standard modulation that synthesizes the mean value required during the control cycle. The converter's performance using the ODPC algorithm improves over existing DPC-based algorithms that use constrained optimization, such as preselected space vectors or switching tables, by providing a further harmonic in content reduction, lower computational requirements, and faster time response to changes in active and reactive power commands. The use of the ODPC results in an almost instantaneous active and reactive power reference tracking, allowing for full power inversion in less than 1.0 ms under constant switching operation. Simulation results and experimental verifications are presented to validate the advantages of the proposed control algorithm. The scope of applications of this technique is those that require low harmonic impact on the ac power supply and for power quality improvement in general.
This work presents a simple scheme for vector selection in direct power control (DPC) in a three-phase rectifier without the use of switch selection tables. The method is simulated using a C language description of the system and its results are later verified on an experimental test rig. Additional states are obtained using space vector modulation (SVM) which reduce the hysteresis band of the active and reactive power controller
1 May 2011 in IEEE Transactions on Power Electronics
This paper presents a dual converter employed as a rectifier with power factor regulation and bidirectional power flow. The active and reactive powers flowing into the converter is controlled using an optimized direct-power-control algorithm. The multilevel structure of the converter is exploited to control the voltage level in each subconverter by selecting the modulation method from one commonly found in the literature, with the option of clamping one of the subconverters. These modulation methods are used to control the power taken by each subconverter, providing limited dc-link voltage regulation. The system is first simulated in SIMULINK, and the results are experimentally validated using a digital-signal-processor-based test rig.
This work presents the design and development of a three-phase multilevel hardware platform for applications in power electronics. The emphasis of the proposed converter is in its flexibility to allow rapid set-ups of different experiments typically required in power electronics teaching and research. The proposed converter uses a cascaded H-bridge topology whereby multilevel operation with up to 9 voltage levels can be obtained. The selected power stage topology as well as the control, drivers and sensors boards designs, enable the platform to operate in multiple configurations, namely as inverter, controlled rectifier or active power filter, for one, two or three-phase systems.
In this work a parameter estimation method of the induction machine model based on the instantaneous impedance is presented. The proposed method is based on instantaneous voltage and current measurements during start-up of the induction motor at rated voltage. The proposed parameter estimation method uses an space vector description of the transient machine equations, referred to the stator frame of reference, during the dynamic conditions presents at start-up. The method adjusts the dynamic model parameters using an error function obtained by comparing the instantaneous impedance obtained from the space vector representation of the machine and the corresponding obtained from the measured variables at start-up. The method gives a very precise off-line parameter estimation. The solution is obtained using a non-linear regression method that can be used to improve the control behavior in several predictive DTC strategies.
The design of robot systems controlled by cables can be relatively difficult when it is approached from the mathematical model of the mechanism, considering that its approach involves non-linearities associated with different components, such as cables and pulleys. In this work, a simple and practical decoupled control structure proposal that requires practically no mathematical analysis was developed for the position control of a planar cable-driven parallel robot (CDPR). This structure was implemented using non-linear fuzzy PID and classic PID controllers, allowing performance comparisons to be established. For the development of this research, first the structure of the control system was proposed, based on an analysis of the cables involved in the movement of the end-effector (EE) of the robot when they act independently for each axis. Then a tuning of rules was carried out for fuzzy PID controllers, and Ziegler–Nichols tuning was applied to classic PID controllers. Finally, simulations were performed in MATLAB with the Simulink and Simscape tools. The results obtained allowed us to observe the effectiveness of the proposed structure, with noticeably better performance obtained from the fuzzy PID controllers.