Redundancy in cable-driven parallel robots provides additional degrees of freedom that can be used to achieve different objectives. In this robot, this degree of freedom is used to act on a reconfigurable end effector with one degree of freedom. A compliant actuator actuated by one motor exerts force on both bodies of the platform. Due to the high tension that appears in this cable in comparison with the rest of the cables, an elastic model was developed for solving the kinestostatic and wrench analysis. A linear sensor was used in one branch of this cable mechanism to provide the needed intermediate values. The position of one link of the platform was fixed in order to focus this analysis on the relationship between the cables and the platform’s internal movement. Position values of the reconfigurable end effector were calculated and measured as well as the tension at different regions of the compliant actuator. The theoretical values were compared with dynamic simulations and real prototype results.
The design of robot systems controlled by cables can be relatively difficult when it is approached from the mathematical model of the mechanism, considering that its approach involves non-linearities associated with different components, such as cables and pulleys. In this work, a simple and practical decoupled control structure proposal that requires practically no mathematical analysis was developed for the position control of a planar cable-driven parallel robot (CDPR). This structure was implemented using non-linear fuzzy PID and classic PID controllers, allowing performance comparisons to be established. For the development of this research, first the structure of the control system was proposed, based on an analysis of the cables involved in the movement of the end-effector (EE) of the robot when they act independently for each axis. Then a tuning of rules was carried out for fuzzy PID controllers, and Ziegler–Nichols tuning was applied to classic PID controllers. Finally, simulations were performed in MATLAB with the Simulink and Simscape tools. The results obtained allowed us to observe the effectiveness of the proposed structure, with noticeably better performance obtained from the fuzzy PID controllers.
Cable-Driven Parallel Robots (CDPR) operate over a large positional workspace and a relatively large orientation workspace. In the present work, the expansion of the orientation Wrench Feasible Workspace (WFW) in a planar four-cable passive reconfigurable parallel robot with three degrees of freedom was determined. To this end, we proposed a circular-geometry effector mechanism, whose structure allows automatic mobility of the two anchor points of the cables supporting the End Effector (EE). The WFW of the proposed circular structure robot was compared with that of a traditional robot with a rectangular geometry and fixed anchor points. Considering the feasible geometric and tension forces on the cables, the generated workspace volume of the robot was demonstrated in an analysis-by-intervals. The results were validated by simulating the orientation movements of the robot in ADAMS software and a real experimental test was developed for a hypothetical case. The proposed design significantly expanded the orientation workspace of the robot. The remaining limitation is the segment of the travel space in which the mobile connection points can slide. Overcoming this limitation would enable the maximum rotation of the EE.
In underwater environments, ensuring people’s safety is complicated, with potentially life-threatening outcomes, especially when divers have to work in deeper conditions. To improve the available solutions for working with robots in this kind of environment, we propose the validation of a control strategy for robots when taking objects from the seabed. The control strategy proposed is based on acceleration feedback in the model of the system. Using this model, the reference values for position, velocity and acceleration are estimated, and then the position error signal can be computed. When the desired position is obtained, it is possible to then obtain the position error. The validation was carried out using three different objects: a ball, a bottle, and a plant. The experiment consisted of using this control strategy to take those objects, which the robot carried for a moment to validate the stabilisation control and reference following the control in terms of angle and depth. The robot was operated by a pilot from outside of the pool and was guided using a camera and sonar in a teleoperated way. As an advantage of this control strategy, the model upon which the robot is based is decoupled, allowing control of the robot for each uncoupled plane, this being the main finding of these tests. This demonstrates that the robot can be controlled by a control strategy based on a decoupled model, taking into account the hydrodynamic parameters of the robot.
Currently, a large number of investigations are being carried out in the area of robotics focused on proposing solutions in the field of health, and many of them have directed their efforts on issues related to the health emergency due to COVID-19. Considering that one of the ways to reduce the risk of contagion is by avoiding contact and closeness between people when exchanging supplies such as food, medicine, clothing, etc., this work proposes the use of a planar cable-driven parallel robot for the transport of supplies in hospitals whose room distribution has planar architecture. The robot acts in accordance with a procedure proposed for each task to be carried out, which includes the process of disinfection (based on Ultraviolet-C light) of the supplies transported inside the robot’s end effector. The study presents a design proposal for the geometry of the planar cable-driven parallel robots and its end effector, as well as the software simulations that allow evaluating the robot’s movement trajectories and the responses of the position control system based on Fuzzy-PID controllers.
El presente articulo presenta la simulación e implementación de un controlador PID, mediante el uso del $software$ MATLAB y LabView. El proceso controlado es un sistema eléctrico de potencia a escala, el cual se encuentra operativo en los laboratorios de la Universidad Politécnica Salesiana de Cuenca. El controlador descrito tiene el objetivo de mantener fijos los valores de frecuencia y voltaje producido por un generador síncrono y un motor trifásico acoplado por sus ejes mediante una banda, ante los distintos agentes externos de perturbaciones como la variación de la carga en la red eléctrica.