Solar-powered photocatalysis has come a long way since its humble beginnings in the 1990s, producing more than a thousand research papers per year over the past decade. In this review, immobilized photocatalysts operating under sunlight are highlighted. First, a literature review of solar-driven films is presented, along with some fundamental operational differences in relation to reactions involving suspended nanoparticles. Common strategies for achieving sunlight activity from films are then described, including doping, surface grafting, semiconductor coupling, and defect engineering. Synthetic routes to fabricate photocatalytically active films are briefly reviewed, followed by the important factors that determine solar photocatalysis efficiency, such as film thickness and structure. Finally, some important and specific characterization methods for films are described. This review shows that there are two main challenges in the study of photocatalytic materials in the form of (thin) films. First, the production of stable and efficient solar-driven films is still a challenge that requires an integrated approach from synthesis to characterization. The second is the difficulty in properly characterizing films. In any case, the research community needs to address these, as solar-driven photocatalytic films represent a viable option for sustainable air and water purification.

Poly(vinyl alcohol) (PVA) biocomposite films reinforced with cellulose nanofibrils (CNF) and biologically active tannic acid (TA) were prepared. The influence of different concentrations of CNF and TA in the PVA polymer matrix was investigated in terms of mechanical properties, thermal properties and hydrophobicity improvement of the prepared films. The results showed that in all cases the addition of CNF and TA improved the values of tensile strength and elastic modulus. The PVA film with 10 % CNF exhibited a 30 % higher tensile strength, and the three-component PVA film with 2 % CNF and 10 % TA (P2C10T) exhibited a 40 % higher tensile strength compared to the neat PVA film. The thermal properties (T_g, T_onset) of the PVA biocomposite films were greatly improved, with a significant effect observed for the three-component PVA films. The T_g of the PVA film with 10 % CNF and 10 % TA was 87 °C, 12 °C higher than that of the neat PVA film. For three-component PVA biocomposites with 4 % and 6 % CNF and with all weight percentages of TA, the T_onset shifted to a higher temperature range by about 30 °C compared to the neat PVA film. The PVA film with 2 % CNF and 10 % TA exhibited about a 20° higher contact angle than the neat PVA film. Moreover, the addition of both fillers to the PVA matrix resulted in PVA biocomposites with lower water absorption. PVA film with 10 % TA absorbed about 90 % less water and PVA film with 10 % CNF and 10 % TA absorbed about 80 % less water than the neat PVA film after the films were soaked in water for one hour. The better properties of the composite films produced are due to hydrogen and ester bonds between the components of the composite, which was confirmed by FT-IR spectroscopy. Antioxidant effective films were also obtained due to the biologically active TA to the PVA and PVA/CNF systems.

Complexes with mixed ligands [Cu(N-N)₂(pmtp)](ClO₄)₂ ((1) N-N: 2,2′-bipyridine; (2) L: 1,10-phenanthroline and pmpt: 5-phenyl-7-methyl-1,2,4-triazolo[1,5-a]pyrimidine) were synthesized and structurally and biologically characterized. Compound (1) crystallizes into space group Pa and (2) in P-1. Both complexes display an intermediate stereochemistry between the two five-coordinated ones. The biological tests indicated that the two compounds exhibited superoxide scavenging capacity, intercalative DNA properties, and metallonuclease activity. Tests on various cell systems indicated that the two complexes neither interfere with the proliferation of Saccharomyces cerevisiae or BJ healthy skin cells, nor cause hemolysis in the active concentration range. Nevertheless, the compounds showed antibacterial potential, with complex (2) being significantly more active than complex (1) against all tested bacterial strains, both in planktonic and biofilm growth state. Both complexes exhibited a very good activity against B16 melanoma cells, with a higher specificity being displayed by compound (1). Taken together, the results indicate that complexes (1) and (2) have specific biological relevance, with potential for the development of antitumor or antimicrobial drugs.

Pre-hydrolysed/condensed tetraethyl orthosilicate (TEOS) was added to a solution of methyl methacrylate (MMA) and 3-methacryloxypropyltrimethoxysilane (MAPTMS), and then copolymerised for various times to study the influence of the latter on the structure of hybrid sol-gel coatings as corrosion protection of aluminium alloy 7075-T6. The reactions taking place during preparation were characterised using real-time Fourier transform infrared spectroscopy, dynamic light scattering and gel permeation chromatography. The solution characteristics were evaluated, using viscosimetry, followed by measurements of thermal stability determined by thermogravimetric analysis. The optimal temperature for the condensation reaction was determined with the help of high-pressure differential scanning calorimetry. Once deposited on 7075-T6 substrates, the coatings were evaluated using a field emission scanning electron microscope coupled to an energy dispersive spectrometer to determine surface morphology, topography, composition and coating thickness. Corrosion properties were tested in dilute Harrison’s solution (3.5 g/L (NH₄)₂SO₄ and 0.5 g/L NaCl) using electrochemical impedance spectroscopy. The copolymerization of MMA and MAPTMS over 4 h was optimal for obtaining 1.4 µm thick coating with superior barrier protection against corrosion attack (|Z_{10 mHz}| ~ 1 GΩ cm²) during three months of exposure to the corrosive medium.

The importance of thermal modification is increasing worldwide. Increased use of thermally modified timber (TMT) has resulted in a need for reliable quality control, comprising control of variation of the production within defined limits, allowing third-party control in the case of certification and the regulation of customer complaints and claims. Techniques are thus needed to characterise the modification of quality in terms of improved target properties of TMT during industrial production, and of TMT products that have been in service for an arbitrary time. In this study, we aimed to utilise dynamic vapor sorption (DVS) for this purpose. Norway spruce (Picea abies) and European beech (Fagus sylvatica) samples were thermally modified at different temperatures according to different heat treatment techniques: (1) the Silvapro process based on an initial vacuum; (2) an air heat treatment, whereby samples were wrapped in aluminium foil; (3) thermal modification of wood samples in the ambient atmosphere in a laboratory oven. Wood samples from closed processes were analysed for validation. TMT was characterised with respect to mass loss, colour and density. Mass loss of wood due to modification (ML_TM) was correlated with factors derived from DVS analysis. The present DVS measurements suggest that the equilibrium wood moisture content (EMC_{95% RH}), the time to reach 10% wood moisture content (t_{10% MC}), and the elongation factor, c, derived from a logarithmic function, can serve as alternative parameters to characterise the quality of several thermal modification processes. Further studies are recommended using other wood species, different modification processes and further parameters gained from DVS measurements to understand the robustness and the predictive power of the applied technique.