In an impressed current cathodic protection system (ICCP) to protect structures against corrosion, the efficient operation depends on the proper selection of the electrodes, particularly the anode, chosen considering the structure to be protected and the environment in which it is located. The nature and overpotential of the anodic reaction determine the operation costs of an ICCP system so that proper anode selection is critically important for an ICCP system to function efficiently. Commercial anodes based on titanium substrates coated with iridium–tantalum oxide mixtures (IrO2-Ta2O5/Ti) are frequently used for this purpose due to low operating overpotentials. However, the gradual passivation of its surface limits its useful life and increases its operating costs, so it is necessary to seek competitive alternatives for its replacement. This study aimed to determine the feasibility of using carbon steel substrates coated with nickel/cobalt/boron (NiCoB/CS) as a viable low-cost alternative to replace IrO2-Ta2O5/Ti anodes in ICCP systems. Comparison between the electrochemical behavior and the corrosion resistance of both types of electrodes shows that the NiCoB/CS anode shows a good electrocatalytic activity and a higher corrosion resistance than IrO2-Ta2O5/Ti coated anodes, indicating that the NiCoB/CS anodes are promising low-cost candidates for ICCP systems.
The manufacture of cellular structures using high-performance materials is possible thanks to the additive manufacturing of metals. However, it is well known that the mechanical and microstructural properties of metals manufactured by this technique do not correspond to those of the same metals manufactured by conventional methods. It is well known that the mechanical properties depend on the direction of manufacture, the size of the pieces, and the type of cell structure used. In addition, the effect of heat treatments on parts manufactured by additive manufacturing differs from parts manufactured by conventional methods. In this work, the microstructure and microhardness of cellular structures of Inconel 718, manufactured by additive manufacturing under heat treatments with different aging times, were evaluated. It was found that the time of the first aging impacts the microhardness and its homogeneity, affecting the microstructure. The highest hardness was obtained for an aging time of 8 h, while the lowest standard deviation was obtained at 10 h. Finally, it is shown that the aging time influences a more homogeneous distribution of the elements and phases.
Experimental and computational approaches were used to study the microstructure of IN718 produced via powder bed fusion additive manufacturing (PBF-AM). The presence, chemical composition, and distribution of stable and metastable phases (γ′′, δ, MC, and Laves) were also analyzed. The information obtained from the microstructural study was used to construct a tailored time–temperature transformation (TTT) diagram customized for additive manufacturing of IN718. Experimental techniques, including differential scanning calorimetry (DSC), scanning electron microscopy, energy dispersive X-ray spectroscopy, and electron backscatter diffraction (EBSD), were employed to establish the morphological, chemical, and structural characteristics of the microstructure. The Thermo-Calc software and a Scheil–Gulliver model were used to analyze the presence and behavior of phase transformations during heating and cooling processes under non-thermodynamic equilibrium conditions, typical of AM processes. Unlike conventional TTT diagrams of this alloy, the diagram presented here reveals that the precipitation of γ′′ and δ phases occurs at lower temperatures and shorter times in AM-manufactured parts. Significantly, the superposition of γ′′ and δ phase curves in the proposed diagram underscores the interdependence between these phases. This TTT diagram is a valuable insight that can help in the development of heat treatment processes and quality control for IN718 produced via PBF-AM.
This work aims to analyze the effect of pore size on the catalytic reaction of 316L stainless steel electrodes. Porous compacts were fabricated using the space holder technique and sintering at low temperatures. The fabricated porous compacts were characterized using computed tomography and the hydrogen evolution reaction was evaluated under 0.5 M and 1.5 M NaOH. Results indicate that porosity is well controlled by the pore formers, which allows different pore size distributions of pores with similar relative density values to be obtained. The pores are fully interconnected, allowing the passing of fluid throughout the compacts. Permeability is sensitive to the pore size, increasing as the pore size does. The catalytic activity of hydrogen evolution reaction HER is improved as the pore volume and pore size increase concerning the compact fabricated without pore formers. The compact that showed higher Cdl and Rf values was fabricated with S100 pore formers, which means a higher active area that favors the HER. It can be concluded that porosity enhances HER reactivity. However, larger pores are not beneficial due to a more significant permeability value.
In this study, the corrosion performance of dissimilar welded joints between ASTM A615 and AISI 304 stainless steel with and without buttering using Inconel 182 was evaluated. In both cases, the filler metal was ER-309L and the base metals were prepared with a 45° single bevel. One half of the specimens were welded with “buttering” using Inconel 182. The electrochemical results showed that despite welding defects, the welded specimens formed a passive layer in alkaline environments. The specimens welded with buttering exhibited the best corrosion resistance and mechanical properties.