The paper is devoted to highlighting the potential application of the quantitative imaging technique through results associated with work hardening, strain rate and heat generated during elastic and plastic deformation. The aim of the research presented in this article is to determine the relationship between deformation in the uniaxial tensile test of samples made of 1-mm-thick nickel-based superalloys and their change in temperature during deformation. The relationship between yield stress and the Taylor–Quinney coefficient and their change with the strain rate were determined. The research material was 1-mm-thick sheets of three grades of Inconel alloys: 625 HX and 718. The Aramis (GOM GmbH, a company of the ZEISS Group) measurement system and high-sensitivity infrared thermal imaging camera were used for the tests. The uniaxial tensile tests were carried out at three different strain rates. A clear tendency to increase the sample temperature with an increase in the strain rate was observed. This conclusion applies to all materials and directions of sample cutting investigated with respect to the sheet-rolling direction. An almost linear correlation was found between the percent strain and the value of the maximum surface temperature of the specimens. The method used is helpful in assessing the extent of homogeneity of the strain and the material effort during its deformation based on the measurement of the surface temperature.
An EN AW-6082 aluminium alloy is one of the 6000 series aluminium alloys with the highest strength properties. Due to its favourable strength-to-density ratio, it is used, among others, in the automotive and aviation applications. It is also characterised by good formability, especially in the annealed condition. This article presents the results of investigations on the possibility of forming a 2 mm thick EN AW-6082 alloy sheet using the incremental sheet-forming process depending on the material condition (O, W, T4, T6). The microstructure of the material after heat treatment and the mechanical properties of the workpiece material in as-received state, as well as after forming, were examined. Additionally, for selected cases, additional heat treatment of the drawpieces was performed to improve their mechanical strength. The values of the limit-forming angle were determined for the materials tested. The values of this angle varied from 69° for the annealed sheet to 61° for the material in the T6 condition. The highest yield stress (YS) and ultimate tensile strength (UTS) were found for sheets (YS = 305 MPs and UTS = 324 MPa) and the artificially aged drawpieces (YS = 333 MPa and UTS = 390 MPa). Additional ageing after incremental sheet forming resulted in an increase in strength properties compared to drawpieces without additional heat treatment only in the case of drawpieces made of sheet metal after the solutionising and in T4 condition.
The extrusion of hollow profiles from hard-deformable AlZnMg alloys by using porthole dies encounters great technological difficulties in practice. High extrusion force accompanies the technological process, which is caused by high deformation resistance and high friction resistance in extrusion conditions. As a result of high thermo-mechanical loads affecting the die, a significant loss of dimensional accuracy of extruded profiles can be observed. The different projects of porthole dies for the extrusion of Ø50 × 2 mm tubes from the 7021 alloy were numerically calculated and then tested in industrial conditions by using a press of 25 MN capacity equipped with a container with a diameter of 7 inches (for 7021 alloy and 6082 alloy for comparison). New extrusion die 3 with modified bridge and mandrel geometry and a special radial–convex entry to the die opening was proposed. FEM was applied to analyse the metal flow during extrusion, geometrical stability of extruded tubes and the die deflection. The photogrammetric measuring method was used to evaluate dimensional accuracy of tubes extruded in different conditions and geometrical deviations in porthole dies elements, especially the bridges and the mandrels. Research revealed a high dimensional accuracy of tubes extruded from the 6082 alloy and from the 7021 alloy by using original extrusion die 3, while much higher dimensional deviations were noted for tubes extruded from the 7021 alloy by using extrusion dies 1 and 2, particularly in relation to the circularity, centricity and wall thickness.
The purpose of this study was to investigate the influence of synthesis parameters and surface finish on the corrosion of DMLS-printed M300 steel components and to evaluate their applicability in corrosive environments. In order to assess the influence of the corrosive environment, potentiodynamic and long-term corrosion tests were carried out in this study, together with microscopic and EDS studies on 3D-printed M300 steel samples synthetized using the DMLS method with different laser powers. The results show that DMLS-produced M300 steel is vulnerable to corrosion in corrosive environments. The effect of the laser power used on the corrosion resistance was also demonstrated, which generally decreases with increasing laser power. This study confirms the influence of the surface condition of the components on the corrosion phenomenon. Despite the higher corrosion resistance of unpolished components, they lose mass to a higher degree in a corrosive environment. This study also shows the influence of temperature on the corrosion phenomena occurring, demonstrating its negative effect. This study also presents the microstructure of the surface of the samples after the tests, showing the degradation of the surface due to corrosive actions. The analysis of the test results suggests the protection of M300 steel components produced using the DMLS method for the case of operation in corrosive environments.
This paper presents the results of a pilot application of Powder-Bed Fusion of Metals Using a Laser (PBF-LB/M) for the fabrication of M300 (1.2709) maraging steel sheet metal bending tools. S235 steel was used as a substrate for the fabrication of bending punches. The main goal of the research was to determine the usability of such tools without heat treatment, which would contribute to the increase in the cost of tool production. Industrial tests of tools were conducted during the forming of Inconel 625 and AW-6061 T0 aluminium alloy sheets. The punches were subjected to tests of surface roughness, hardness, microstructure, porosity, and geometric quality in order to verify the quality and accuracy of tools made by the PBF-LB/M technique before and after experimental investigations in industrial conditions in a selected manufacturing company. It was found that tools with an M300 steel working layer after the PBF-LB/M process without heat treatment show suitability for bending sheet metal in a certain range of force parameters, ensuring obtaining elements after bending from Inconel 625 and AW-6061 T0 aluminium alloy sheets of the required geometric quality.
This article presents a study on the effect of strain rate, specimen orientation, and plastic strain on the value and distribution of the temperature of dog-bone 1 mm-thick specimens during their deformation in uniaxial tensile tests. Full-field image correlation and infrared thermography techniques were used. A titanium-stabilised austenitic 321 stainless steel was used as test materials. The dog-bone specimens used for uniaxial tensile tests were cut along the sheet metal rolling direction and three strain rates were considered: 4 × 10−3 s−1, 8 × 10−3 s−1 and 16 × 10−3 s−1. It was found that increasing the strain rate resulted in the intensification of heat generation. High-quality regression models (Ra > 0.9) developed for the austenitic 321 steel revealed that sample orientation does not play a significant role in the heat generation when the sample is plastically deformed. It was found that at the moment of formation of a necking at the highest strain rate, the maximum sample temperature increased more than four times compared to the initial temperature. A synergistic effect of the strain hardening exponent and yield stress revealed that heat is generated more rapidly towards small values of strain hardening exponent and yield stress.