Hydrometallurgical recovery of zinc from electric arc furnace dust was investigated on a laboratory scale, using aqueous sodium hydroxide solution as a leaching agent. Special attention was paid to the effect of NaOH concentration, temperature and liquid/solid phase ratio on the zinc leachability. It was found that all tested factors increased the leachability, with the maximum efficiency of 88% obtained in a 6 M NaOH solution at a temperature of 80 °C and the liquid/solid phase ratio of 40. The test results confirmed the high selectivity of the zinc leaching agent. In spite of this, complete recovery of zinc from steelmaking dust has proved to be very difficult due to the occurrence of this element in the form of stable and sparingly soluble ZnFe₂O₄ ferrite. Purification of the solution by cementation and electrolysis gave zinc of purity 99.88% in powder form.

Recent work indicates that the high-velocity oxy-fuel (HVOF) thermal spraying WC–Co coatings have been used to enhance the wear resistance of various engineering components in a variety of industrial environments. In the present work, WC–Co powder, containing Cr particles in an amount of 10%, was deposited on ductile cast iron with the HVOF thermal spray coating technique. An investigation was conducted to determine the role of Cr particles in the WC–Co coating produced with the HVOF technique on microstructure, mechanical, and wear properties in a system of type: WC-Co coating/ductile cast iron. The microstructure of the HVOF-sprayed WC–Co + Cr coating was characterised by light microscopy, X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and energy-dispersive X-ray spectroscopy (EDS). The analysis of the microstructure showed the formation of a coating with low porosity, compact structure, and good adhesion to the substrate with a typical lamellar structure composed of fine molten Cr particles and finely fragmented WC grains embedded in a Co matrix, reaching the size of nanocrystalline. The scratch test was applied for the analysis of the adhesion of coatings to the substrate. The erosion behaviour and mechanism of material removal was studied and discussed based on microstructural examinations. Moreover, the results were discussed in relation to the bending strength test, including cracks and delamination in the system of the WC–Co + Cr/ductile cast iron, as microhardness and erosion resistance of the coating. It was found that the addition of Cr particles to the WC–Co powder, which causes hardening of the binder phase is a key influence on increased mechanical and wear properties in the studied system. Additionally, due to the construction of nanostructured coatings, suitable proportion of hard and soft phases, the technique sprayed HVOF coatings have advantageous properties such as high density and good slurry erosion resistance.

The article presents the results of research on the influence of plastic deformation on the microstructure and tensile strength of Haynes 282 nickel superalloy produced by direct metal laser sintering (DMLS) and a conventional technique (casting). Samples were tested for dimensional accuracy using a 3D scanner. Then, the samples were subjected to plastic deformation by rolling. The microstructures of the DMLS and the as-cast samples were analysed using a scanning electron microscope. The strength properties of the samples were determined in a static tensile test. Microhardness measurements of the samples were also performed. Based on the analysis of the dimensional accuracy, it was found that the surface quality of the components produced by DMLS is dependent on the input parameters of the 3D printing process. Using the DMLS method, it is possible to produce Haynes 282 with a fine-crystalline microstructure containing dendrites. The fine-crystalline dendritic microstructure and low porosity showed very good tensile strength compared to the as-cast material. It was also found that the increase in the degree of plastic deformation of the as-cast Haynes 282 and the samples produced by the DMLS technique resulted in an increase in the strength of the tested samples, with reduced ductility.

The purpose of this study was to investigate the influence of synthesis parameters and surface finish on the corrosion of DMLS-printed M300 steel components and to evaluate their applicability in corrosive environments. In order to assess the influence of the corrosive environment, potentiodynamic and long-term corrosion tests were carried out in this study, together with microscopic and EDS studies on 3D-printed M300 steel samples synthetized using the DMLS method with different laser powers. The results show that DMLS-produced M300 steel is vulnerable to corrosion in corrosive environments. The effect of the laser power used on the corrosion resistance was also demonstrated, which generally decreases with increasing laser power. This study confirms the influence of the surface condition of the components on the corrosion phenomenon. Despite the higher corrosion resistance of unpolished components, they lose mass to a higher degree in a corrosive environment. This study also shows the influence of temperature on the corrosion phenomena occurring, demonstrating its negative effect. This study also presents the microstructure of the surface of the samples after the tests, showing the degradation of the surface due to corrosive actions. The analysis of the test results suggests the protection of M300 steel components produced using the DMLS method for the case of operation in corrosive environments.

This paper presents the results of a pilot application of Powder-Bed Fusion of Metals Using a Laser (PBF-LB/M) for the fabrication of M300 (1.2709) maraging steel sheet metal bending tools. S235 steel was used as a substrate for the fabrication of bending punches. The main goal of the research was to determine the usability of such tools without heat treatment, which would contribute to the increase in the cost of tool production. Industrial tests of tools were conducted during the forming of Inconel 625 and AW-6061 T0 aluminium alloy sheets. The punches were subjected to tests of surface roughness, hardness, microstructure, porosity, and geometric quality in order to verify the quality and accuracy of tools made by the PBF-LB/M technique before and after experimental investigations in industrial conditions in a selected manufacturing company. It was found that tools with an M300 steel working layer after the PBF-LB/M process without heat treatment show suitability for bending sheet metal in a certain range of force parameters, ensuring obtaining elements after bending from Inconel 625 and AW-6061 T0 aluminium alloy sheets of the required geometric quality.

Ensuring adequate reliability of the production process of packaging closures has made it necessary to study the effect of annealing and varnishing variants on the strength and structural properties of the stock material. As a test material, EN AW-5052-H28 aluminium alloy sheets with a thickness of 0.21 mm were used. The surface treatment of the test material involved varnishing the sheet metal surface using various varnishes and soaking the sheet metal. The coefficient of friction and the abrasion resistance of the coatings were determined using the T-21 ball-and-disc tribotester. The tested sheets were subjected to tribological analysis by the T-05 roller-block tribotester using countersamples made of Caldie and Sverker 21 tool steels. The results of the tests showed differences in mechanical and structural properties depending on the method of sample preparation. Based on the test results, significant differences in the adhesion of anti-wear coatings were found. The results revealed that the most favourable friction conditions are provided by the CrN coating. The (AlTi)N interlayer in the (AlTi)N/(AlCr)N coating adheres to the substrate over the entire tested area and no detachment from its surface was observed, which proves good bonding at the substrate/coating interface. The tested AlTiN/TiAlSiXN coating is characterised by a more homogeneous, compact microstructure compared to the (AlTi)N/(AlCr)N coating.