In this study, nano-BaTiO3 (BTO) powders were obtained via the solvothermal method at different reaction times and were investigated using transmission electron microscopy (TEM), X-ray diffraction (XRD) and Raman spectroscopy. The results were compared with those obtained for a larger crystallite size BTO powder (BTO-m). The sizes of the cuboid crystallites (as determined by XRD and TEM) ranged from about 18 to 24 nm, depending on the reaction time. The evolution with temperature of the structure parameters of nano-BTO was monitored by means of X-ray diffraction and Raman spectroscopy and no signs of phase transition were found up to 170 °C. Careful monitoring of the dependence of the XRD peak widths on the hkl indices showed that the effect of the cubic crystallite shape upon the XRD peak widths was buried by the effect of hidden tetragonal line splits and by anisotropic microstrain. The good correlation of the line widths with the tetragonal split amplitudes, observed especially for BTO-m above the transition temperature, indicates tetragonal deformations, as also revealed by Raman spectroscopy. The large anisotropic microstrain shown by the nano-powders, which had a maximum value in the directions, was considered evidence of the phenomenon of surface relaxation of cubic crystallites edged by {100} faces. The observed behavior of the nano-BTO structures with increasing temperature may suggest a correlation between the surface relaxation and tetragonal deformation in the nano-cubes. The experimental results for both nano-BTO and mezoscale-BTO are in agreement with the core-shell model.
26 February 2021 in Physica Status Solidi (RRL) – Rapid Research Letters
Thin film metal–ferroelectric–metal capacitors with an equal mixture of hafnium oxide and zirconium oxide as the ferroelectric material are fabricated using iridium oxide as the electrode material. The influence of the oxygen concentration in the electrodes during crystallization anneal on the ferroelectric properties is characterized by electrical, chemical, and structural methods. Forming gas, O2, and N2 annealing atmospheres significantly change the ferroelectric performance. The use of oxygen‐deficient electrodes improves the stabilization of the ferroelectric orthorhombic phase and reduces the wake‐up effect. It is found that oxygen‐rich electrodes supply oxygen during anneal and reduce the amount of oxygen vacancies, but the nonferroelectric monoclinic phase is stabilized with a negative impact on the ferroelectric properties.
In this work, the metal and semiconducting nanoparticles (AgNPs, ZnONPs and AgZnONPs) were phyto-synthesized using aqueous vegetal extracts from: Caryophyllus aromaticus L. (cloves) and Citrus reticulata L. (mandarin) peels. The morphological, structural, compositional, optical and biological properties (antibacterial activity, and cytotoxicity) of the prepared composites were investigated. The most effective sample proved to be AgZnONPs, derived from cloves, with a minimum inhibitory concentration (MIC) value of 0.11 mg/mL and a minimum bactericidal concentration (MBC) value of 2.68 mg/mL. All the other three composites inhibited bacterial growth at a concentration between 0.25 mg/mL and 0.37 mg/mL, with a bactericidal concentration between 3 mg/mL and 4 mg/mL. The obtained composites presented biocidal activity against Staphylococcus aureus, and biocompatibility (on human fibroblast BJ cells) and did not damage the human red blood cells. Additionally, an important result is that the presence of silver in composite materials improved the bactericidal action of these nanomaterials against the most common nosocomial pathogen, Staphylococcus aureus.
Structural and electrical properties of epitaxial Pb(Zr0.2Ti0.8)O3 films grown by pulsed laser deposition from targets with different purities are investigated in this study. One target was produced in-house by using high purity precursor oxides (at least 99.99%), and the other target was a commercial product (99.9% purity). It was found that the out-of-plane lattice constant is about 0.15% larger and the a domains amount is lower for the film grown from the commercial target. The polarization value is slightly lower, the dielectric constant is larger, and the height of the potential barrier at the electrode interfaces is larger for the film deposited from the pure target. The differences are attributed to the accidental impurities, with a larger amount in the commercial target as revealed by composition analysis using inductive coupling plasma-mass spectrometry. The heterovalent impurities can act as donors or acceptors, modifying the electronic characteristics. Thus, mastering impurities is a prerequisite for obtaining reliable and reproducible properties and advancing towards all ferroelectric devices.
Polarization switching in ferroelectric films is exploited in many applications, such as non-volatile memories and negative capacitance field affect transistors. This can be inhomogeneous or homogeneous, depending on if ferroelectric domains are forming or not during the switching process. The relation between the polarization switching, the structural quality of the films and the negative capacitance was not studied in depth. Here, Pb(Zr0.2Ti0.8)O3 (PZT) layers were deposited by pulse laser deposition (PLD) and sol-gel (SG) on single crystal SrTiO3 (STO) and Si substrates, respectively. The structural quality was analyzed by X-ray diffraction and transmission electron microscopy, while the electric properties were investigated by performing hysteresis, dynamic dielectric measurements, and piezo-electric force microscopy analysis. It was found that the PZT layers grown by PLD on SRO/STO substrates are epitaxial while the layers deposited by SG on Pt/Si are polycrystalline. The polarization value decreases as the structure changes from epitaxial to polycrystalline, as well as the magnitude of the leakage current and of the differential negative capacitance, while the switching changes from homogeneous to inhomogeneous. The results are explained by the compensation rate of the depolarization field during the switching process, which is much faster in epitaxial films than in polycrystalline ones.
Layers of HfO 2 and (Hf,Zr)O 2 crystalline nano‐particles are synthesized via direct liquid injection atomic layer deposition, and a comprehensive set of structural, chemical, and electrical characterizations is employed to elucidate their phase composition and functional behavior. X‐ray photoelectron spectroscopy revealed a compositional contrast between the films: (Hf,Zr)O 2 layers contained up to 45% stoichiometric oxide, while pure HfO 2 films are dominated by sub‐oxides, especially under strongly reducing conditions, in which exclusively sub‐oxide phases and p‐type semiconducting behavior is revealed. Electrical measurements indicated room‐temperature stabilization of polar phases and tetragonal‐to‐orthorhombic phase transition with a Curie temperature near 200 K. FTIR spectroscopy confirmed the presence of tetragonal and orthorhombic HfO 2 phases, providing insight into minor features observed ≈30° (2θ) in X‐ray diffraction patterns. Notably, devices incorporating an AlN interlayer demonstrated a significant enhancement in pyroelectric performance, suggesting this strategy to advance the pyroelectric performance of HfO 2 ‐based materials, supporting their development for lead‐free sensor technologies.