Focused microwave−hyperthermia therapy has recently emerged as a key technology in the treatment of breast cancer due to non−invasive treatment. An applicator of a three−ring phased array consisting of ultra−wideband (UWB) microstrip antennas was designed for breast cancer therapy and operates at 0.915 GHz and 2.45 GHz. The proposed antenna has an ultra−wideband from 0.7 GHz to 5.5 GHz with resonant frequencies of 0.915 GHz and 2.45 GHz and dimensions of 15 × 43.5 × 1.575 mm3. The number of each ring was chosen to be 12 based on the SAR distribution and the performance indicators of tumor off−center focusing results for four different numbers of single−ring arrays. The homogeneous breast model is applied to a three−ring phased array consisting of 36 elements for focused simulation, and 1 cm3 and 2 cm3 tumors are placed in three different locations in the breast. The simulation results show that the proposed phased array has good performance and the capability to raise the temperature of different volumes of breast cancer above 42.5 °C after choosing a suitable operating frequency. The proposed applicator allows for precise treatment of tumors by selecting the appropriate operating frequency based on the size of the malignant tumor.
Microwave hyperthermia using the phased array applicator is a non-invasive treatment modality for breast cancer. Hyperthermia treatment planning (HTP) is critical to accurately treating breast cancer and avoiding damage to the patient’s healthy tissue. A global optimization algorithm, differential evolution (DE) algorithm, has been applied to optimize HTP for breast cancer and its ability to improve the treatment effect was proved by electromagnetic (EM) and thermal simulation results. DE algorithm is compared to time reversal (TR) technology, particle swarm optimization (PSO) algorithm, and genetic algorithm (GA) in HTP for breast cancer in terms of convergence rate and treatment results, such as treatment indicators and temperature parameters. The current approaches in breast cancer microwave hyperthermia still have the problem of hotspots in healthy tissue. DE enhances focused microwave energy absorption into the tumor and reduces the relative energy of healthy tissue during hyperthermia treatment. By comparing the treatment results of each objective function used in DE, the DE algorithm with hotspot to target quotient (HTQ) as the objective function has outstanding performance in HTP for breast cancer, which can increase the focused microwave energy of the tumor and decrease the damage to healthy tissue.
Diagonal loading technology is widely used in array antenna beamforming because of its simple method, low computational complexity and the ability to improve the robustness of beamformer. On this basis, this paper proposes a robust adaptive beamforming method based on automatic variable loading technology. The automatic variable loading matrix (AVLM) of the method is composed of two parts. The non-uniform loading matrix dominants when the input signal-to-noise ratio (SNR) is small, effectively control the influence of noise disturbance without affecting the ability of array antenna to suppress interference. The variable diagonal loading matrix dominants when the input SNR is high to improve the output performance of array antenna. Simulated results show that compared to other methods, the proposed method has better output performance for both low and high input SNR cases.
2 January 2022 in International Journal of Electronics
When the rapid moving interference exists, especially in the presence of look direction mismatch, coherent local scattering and so on, the output performance of beamformer will degrade dramatically. To solve this problem, a novel robust adaptive null broadening beamforming method based on subspace projection is proposed. First, the proposed beamformer requires a priori information, that is, the spatial sector where the desired signal and interference may locate, so as to construct the signal-plus-noise covariance matrix (SPNCM) and interference-plus-noise covariance matrix (IPNCM). Then, the desired signal steering vector (SV) is calibrated twice. The desired signal SV is estimated from the SPNCM and subsequently calibrated by using the uncertainty set optimization method. Next, we construct the null broadening projection matrix by tapering the interference subspace got from IPNCM. Finally, the sample covariance matrix (SCM) is processed by projection technology and diagonal loading technology. The optimal weight vector is obtained by the new covariance matrix and calibrated desired signal SV. Simulation results show that the proposed method can form wide null in the incident direction of interference and prevent interference from moving out of the null when the rapid moving interference exists. The proposed method outperforms other existing methods.