Traditional Chinese wood residences consist of timber frames with masonry infill walls or other types of infill, representing valuable heritage. A field investigation of traditional village dwellings in northern China consisting of timber frames with mud and stone infill walls was conducted. Their construction characteristics are reported, and static cyclic tests were performed on two full-size wood-stone hybrid walls with different configurations (exterior transverse wall and internal transverse wall) and no openings (doors or windows). Their failure mechanics and seismic capacity, i.e., the strength, stiffness, ductility, and energy dissipation, were investigated. The results are compared with a previous experimental study of two full-size timber frames with the same traditional structure but no infill to determine the effect of the mud and stone infill on the lateral resistance. The experimental results indicate that the stone infill has a critical influence on the lateral performance of traditional village buildings, resulting in a high lateral stiffness, high strength (>20 kN), and a high ductility ratio (>10). An increase in the vertical load leads to an increase in the lateral resistance of the timber frame with infill walls, larger for the internal transverse wall than the external gable wall. The incompatibility of the deformation between the timber frame and stone infill is the main failure reason, resulting in falling stones and collapse with undamaged timber frames. Suggestions are provided for the protection and repair of traditional wood residences in northern China.

Wood is an anisotropic material, the mechanical properties of which are strongly influenced by its microstructure. In wood, grain compression strength and modulus are the weakest perpendicular to the grain compared to other grain directions. FE (finite element) models have been developed to investigate the mechanical properties of wood under transverse compression. However, almost all existing models were deterministic. Thus, the variations of geometry of the cellular structure were not considered, and the statistical characteristic of the mechanical property was not involved. This study aimed to develop an approach to investigate the compression property of wood in a statistical sense by considering the irregular geometry of wood cells. First, the mechanical properties of wood under radial perpendicular to grain compression was experimentally investigated, then the statistical characteristic of cell geometry was extracted from test data. Finally, the mechanical property of wood was investigated using the finite element method in combination with the Monte Carlo Simulation (MCS) techniques using randomly generated FE models. By parameter sensitivity analysis, it was found that the occurrence of the yield points was caused by the bending or buckling of the earlywood axial tracheid cell wall in the tangential direction. The MCS-based stochastic FE analysis was revealed as an interesting approach for assessing the micro-mechanical performance of wood and in assisting in understanding the mechanical behavior of wood based on its hierarchical structure.

With the increasing popularity of cross-laminated timber (CLT) constructions around the world, there have been attempts to produce CLT using local wood species in different countries, such as Japanese larch (Larix kaempferi (Lamb.) Carr.) in China. Thus, the need to investigate the connection performance also increases to support the design and construction of CLT buildings using local wood species. In this study, the withdrawal properties of three different types of self-tapping screws (STS), with a diameter of 6 mm, 8 mm, and 11 mm, were tested with Japanese larch CLT. The results revealed that the withdrawal strength of STS increased with increasing density and effective length, but decreased with an increasing diameter. With a density increment of 0.05 g/cm³, the withdrawal strength increased by an average of 9.4%. With an effective length increment of 24 mm, the withdrawal strength increased by an average of 1.4%. An empirical regression model was adopted to predict the withdrawal strength of Japanese larch CLT based on the results, which can be used for potential engineering design of CLT connections using STS.

Cross-laminated timber (CLT) elements are becoming increasingly popular in multi-storey timber-based structures, which have long been built in many different countries. Various challenges are connected with constructions of this type. One such challenge is that of stabilizing the structure against vertical loads. However, the calculations of the stability bearing capacity of the CLT members in axial compression in the structural design remains unsolved in China. This study aims to determine the stability bearing capacity of the CLT members in axial compression and to propose the calculation method of the stability coefficient. First, the stability coefficient calculation theories in different national standards were analyzed, and then the stability bearing capacity of CLT elements with four slenderness ratios was investigated. Finally, based on the stability coefficient calculation formulae in the GB 50005-2017 standard and the regression method, the calculation method of the stability coefficient for CLT elements was proposed, and the values of the material parameters were determined. The result shows that the average deviation between fitting curve and calculated results of European and American standard is 5.43% and 3.73%, respectively, and the average deviation between the fitting curve and the actual test results was 8.15%. The stability coefficients calculation formulae could be used to predict the stability coefficients of CLT specimens with different slenderness ratios well.

Rolling shear modulus and strength are the key factors affecting the mechanical performance of some wood products such as cross-laminated timber (CLT). As reported, rolling shear property strongly depends on the sawing pattern such as the aspect ratio and grain direction (grain mode). However, the mechanism behind this phenomenon has not yet been clarified. In this work, the rolling shear modulus and strength of spruce-pine-fir (SPF) with different grain modes and aspect ratios were experimentally investigated. In addition, a theoretical investigation was carried out to reveal the mechanism behind this phenomenon. The results exhibited that the rolling shear moduli of 0° and 90° grain-mode wood were the same. This value can be called the pure rolling shear modulus. Rolling shear modulus of wood with angles other than 0° and 90° can be calculated from the pure rolling shear modulus and grain angle. Therefore, this modulus can be called the apparent rolling shear modulus. Thus, using 0° and 90° grain-mode specimens to determine the pure rolling shear modulus and strength of wood is recommended.