Traditional Multi-Criteria Decision Making (MCDM) methods have now become outdated; therefore, most researchers are focusing on more robust hybrid MCDM models that combine two or more MCDM techniques to address decision-making problems. The authors attempted to create two novel hybrid MCDM systems in this paper by integrating Additive Ratio ASsessment (ARAS) with Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) and Complex PRoportional ASsessment (COPRAS). To demonstrate the ability and effectiveness of these two hybrid models i.e., TOPSIS-ARAS and COPRAS-ARAS were applied to solve a real-time robot selection problem with 12 alternative robots and five selection criteria, while evaluating the parametric importance using the CRiteria Importance Through Inter criteria Correlation (CRITIC) objective weighting estimation tool. The rankings of the robot alternatives gained from these two hybrid models were also compared to the obtained results from eight other solo MCDM tools. Although the rankings by the applied methods slightly differ from each other, the final outcomes from all of the adopted techniques are consistent enough to suggest that robot 12 is the best choice followed by robot 11, and robot 4 is the worst one among these 12 alternatives. Spearman Correlation Coefficient (SCC) also reveals that the proposed rankings derived from various methods have a strong ranking relationship with one another. Finally, sensitivity analysis was performed to investigate the effects of weight variation and to validate the robustness of the implemented MCDM approaches.
In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.
Over the past few years, natural fiber composites have been a strategy of rapid growth. The computational methods have become a significant tool for many researchers to design and analyze the mechanical properties of these composites. The mechanical properties such as rigidity, effects, bending, and tensile testing are carried out on natural fiber composites. The natural fiber composites were modeled by using some of the computation techniques. The developed convolutional neural network (CNN) is used to accurately predict the mechanical properties of these composites. The ground‐truth information is used for the training process attained from the finite element analyses below the plane stress statement. After completion of the training process, the developed design is authorized using the invisible data through the training. The optimum microstructural model is identified by a developed model embedded with a genetic algorithm (GA) optimizer. The optimizer converges to conformations with highly enhanced properties. The GA optimizer is used to improve the mechanical properties to have the soft elements in the area adjacent to the tip of the crack.
Powder-based additive manufacturing (PAM) is a potential fabrication approach in advancing state-of-the-art research to produce intricate components with high precision and accuracy in near-net form. In PAM, the raw materials are used in powder form, deposited on the surface layer by layer, and fused to produce the final product. PAM composite fabrication for biomedical implants, aircraft structure panels, and automotive brake rotary components is gaining popularity. In PAM composite fabrication, the aluminium cast alloy is widely preferred as a metal matrix for its unique properties, and different reinforcements are employed in the form of oxides, carbides, and nitrides. However, for enhancing the mechanical properties, the carbide form is predominantly considered. This comprehensive study focuses on contemporary research and reveals the effect of metal carbide’s (MCs) addition to the aluminium matrix processed through various PAM processes, challenges involved, and potential scopes to advance the research.
4 October 2023 in International Journal on Interactive Design and Manufacturing (IJIDeM)