Anna Wojtacha

Ms. Anna Wojtacha

Silesian University of Technology
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 September 2024 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Open access
PDF file
AWAnna Wojtacha
Anna Wojtacha
Aleksandra KozlowskaAleksandra Kozlowska
Aleksandra Kozlowska
MMMateusz Morawiec
Mateusz Morawiec
MOMarek Opiela
Marek Opiela
In this work, the phase transformation kinetics and precipitation processes were studied using thermodynamic calculations and a dilatometric method to determine the optimal chemical composition of medium-Mn steel and its initial parameters of heat treatment. The investigated steel is intended for forgings with the microstructure composed of bainitic matrix and retained austenite (RA). An influence of Al and Si on the Ms temperature was characterized to obtain the best chemical composition in terms of RA stabilization. Theoretical continuous cooling transformation (CCT) and time–temperature transformation (TTT) diagrams were determined and compared with dilatometric results. Microstructural observations were compared with the dilatometric results. The hardenability of steel was high due to increased Mn and Mo additions. A very small fraction of cementite is expected in the microstructure due to Al and Si additions. The shortest time to start and finish the bainitic transformation was noted for the isothermal heat treatment at 420 °C. The completion of the bainitic transformation took about 25 min and is acceptable from the industrial point of view. The obtained results constitute a good basis for designing thermomechanical processing routes of bainitic steels with RA.

12 June 2021 in Materials
Verified
Journal Article
Open access
PDF file
AWAnna Wojtacha
Anna Wojtacha
MKMonika Kciuk
Monika Kciuk
MOMarek Opiela
Marek Opiela
The article presents the results of the research on the influence of heat treatment conditions on corrosion resistance of newly developed HSLA-type (High Strength Low Alloy) steel in selected corrosive environments. Laboratory tests were carried out with using a salt spray chamber, enabling the continuous spraying of brine mist (5% NaCl) during 96 h under high humidity conditions. Additionally, as part of corrosion experiments, tests were carried out using the gravimetric method, in which the intensity of corrosive processes was measured by the linear corrosion rate. The research conducted revealed that the best corrosion resistance was noted for steel with a high-temperature tempered martensite microstructure. Investigated 0.28C–1.4Mn–0.3Si–0.26Cr steel with Nb, Ti, and V microadditions can be used in offshore drilling constructions and production platforms exposed to salts present in sea water, chlorides, sulfates, carbonates, and bromides, among others.

30 March 2021 in Materials
Verified
Journal Article
Open access
PDF file
MMMateusz Morawiec
Mateusz Morawiec
AWAnna Wojtacha
Anna Wojtacha
MOMarek Opiela
Marek Opiela
This work presents the results of phase transformation kinetics during continuous cooling in newly developed high strength low-alloy steel (HSLA). Initial theoretical calculations for the determination of heat treatment parameters were conducted. To determine the structural constituents formed due to the austenite decomposition the dilatometry approach was used. The material was cooled down from the austenitization temperature of 1000 °C with cooling rates between 0.1 °C/s to 60 °C/s. Then, light and scanning electron microscopy investigations were carried out. The microstructure after cooling at rates between 0.1 °C/s up to 1 °C/s is mainly ferritic with some fraction of granular bainite. Increasing the cooling rate led to formation of a higher fraction of bainitic ferrite. At 60 °C/s the microstructure was mainly bainite with some fraction of ferrite. To determine the presence of retained austenite, color etching using Klemm solution was used. The results show that the increase of cooling rate decreases the amount of retained austenite in the microstructure of the steel. Hardness measurements were made to determine the changes in the mechanical properties as a function of the cooling rate.

28 December 2025 in Materials
Verified
Journal Article
Open access
PDF file
Aleksandra KozlowskaAleksandra Kozlowska
Aleksandra Kozlowska
AWAnna Wojtacha
Anna Wojtacha
This review highlights conventional forging steels and advanced medium-Mn steels containing retained austenite (RA), emphasizing their potential for industrial forging applications. Modern steels intended for forgings are required to combine strength, ductility, toughness and fatigue resistance with good hardenability and machinability at minimal cost. Medium-Mn multiphase steels fulfill these requirements by the strain-induced martensitic transformation (SIMT) of fine, lath-type RA, which can create a strength–ductility balance. Ferritic–austenitic steels provide high ductility with moderate strength, martensitic–austenitic steels show very high strength at the expense of ductility, and bainitic–austenitic steels achieve intermediate properties. Impact toughness and fatigue resistance are strongly influenced by the morphology of RA. The lath-type RA enhances energy absorption and delays crack initiation, while blocky RA may promote intergranular fracture. Low carbon (0.2–0.3 wt.%) combined with elevated manganese (3–7 wt.%) contents provides superior hardenability and machinability, enabling cost-effective air-hardening of components with various cross-sections. Advanced medium-Mn steels provide a superior mechanical performance and economically attractive solution for modern forgings, exceeding the limitations of conventional steel grades.

31 May 2025 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
MMMateusz Morawiec
Mateusz Morawiec
JOJarosław Opara
Jarosław Opara
ASAdam Skowronek
Adam Skowronek
AKAlireza Kalhor
Alireza Kalhor
Aleksandra KozlowskaAleksandra Kozlowska
Aleksandra Kozlowska
AGAdam Grajcar
Adam Grajcar

1 January 2021 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
AWAnna Wojtacha
Anna Wojtacha
MOMarek Opiela
Marek Opiela
The aim of the work was to determine the diagrams of phase evolution under equilibrium conditions and numerical simulation of austenite phase transformations under non-equilibrium conditions, as well as to determine CCT (Continuous Cooling Transformation) and TTT (Temperature Time Transformation) diagrams with the use of JMatPro software. The subject of the analysis were two newly elaborated multiphase steels assigned for production of forgings: steel A, containing of 0.165% C, 2% Mn, 1.11% Si and steel B, containing 0.175% C, 1,87% Mn, 1% Si, 0.22% Mo and Ti and V microadditions at a concentration of 0.031% and 0.022%, respectively. The performed simulation revealed that the investigated steels have similar critical temperatures under equilibrium conditions: A(c1) similar to 680 degrees C, A(c3) similar to 830 degrees C. The chemical composition of steel B and the interaction of Mo, Ti and V in particular, determine that diffusion transformations, i.e. ferritic and pearlitic, in the elaborated CCT and TTT diagrams are significantly shifted to longer times in relation to the position of these transformations in the diagrams for steel A. A distinct delay also concerns the bainitic transformation. Moreover, it was found that the M, temperature of steel B is slightly lower. The determined CCT and TTT diagrams are essentially helpful in the development of heat and thermo-mechanical treatment conditions for new steel grades.