Monika Kciuk

Dr. Monika Kciuk

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 April 2016 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
AGAdam Grajcar
Adam Grajcar
MKMonika Kciuk
Monika Kciuk
STS. Topolska
S. Topolska
APA. Płachcińska
A. Płachcińska
The electrochemical corrosion properties of 26Mn-3Si-3Al and 27Mn-4Si-2Al austenitic steels in two different states were studied in 0.1 M H2SO4 and 3.5% NaCl using potentiodynamic polarization tests. The effect of cold deformation on the microstructure and corrosion behavior of steels was analyzed. In acid solution, both steels exhibited lower corrosion resistance than in chloride solution independently on the steel state (hot-rolled, cold-worked). Cold deformation decreases the corrosion resistance, though this effect is smaller than the effect of chemical composition related to the combined Al + Si addition. All steels showed the evidence of pitting corrosion. The intensive dissolution of Fe and Mn takes place in the acid medium.

10 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
Jacek GórkaJacek Górka
Jacek Górka
WSWojciech Suder
Wojciech Suder
MKMonika Kciuk
Monika Kciuk
SSSebastian Stano
Sebastian Stano
This study discusses the effect of laser beam welding parameters on the structure, mechanical properties and corrosion resistance of 1.2 mm thick galvanized sheets made of low-carbon steel DC04 provided with a ZE36/36 GardoprotectOC2BU organic coating. The test laser beam butt welded joints were made without the filler metal, using a variable welding rate, where linear welding energy was restricted within the range of 30 J/mm to 90 J/mm. The joints were subjected to non-destructive tests, destructive tests and corrosion resistance tests. The tests revealed the possibility of making joints meeting the criteria specified in the ISO 15614-11 standard. Regardless of the value of linear welding energy applied in the process, all the joints were characterised by high mechanical and plastic properties. It was noticed that an increase in linear welding energy from 30 J/mm to 90 J/mm was accompanied by the widening of the weld and that of the heat-affected zone (HAZ). In addition, an increase in linear welding energy was accompanied by a decrease in the maximum weld hardness to approximately 250 HV0.2. In the HAZ, hardness was restricted within the range of 190 HV0.2 to 230 HV0.2 and decreased along with increasing linear welding energy. In the static tensile test, regardless of the value of linear welding energy, the test specimen ruptured in the base material. In the bend test, regardless of the value of linear welding energy, a bend angle of 180° was obtained without partial tear or scratches; unit elongation was restricted within the range of 29% to 42%. The electrochemical tests and experiments performed in the salt spray chamber revealed the very high effectiveness of the corrosion protections against aggressive chloride ions.

12 June 2021 in Materials
Verified
Journal Article
Open access
PDF file
AWAnna Wojtacha
Anna Wojtacha
MKMonika Kciuk
Monika Kciuk
MOMarek Opiela
Marek Opiela
The article presents the results of the research on the influence of heat treatment conditions on corrosion resistance of newly developed HSLA-type (High Strength Low Alloy) steel in selected corrosive environments. Laboratory tests were carried out with using a salt spray chamber, enabling the continuous spraying of brine mist (5% NaCl) during 96 h under high humidity conditions. Additionally, as part of corrosion experiments, tests were carried out using the gravimetric method, in which the intensity of corrosive processes was measured by the linear corrosion rate. The research conducted revealed that the best corrosion resistance was noted for steel with a high-temperature tempered martensite microstructure. Investigated 0.28C–1.4Mn–0.3Si–0.26Cr steel with Nb, Ti, and V microadditions can be used in offshore drilling constructions and production platforms exposed to salts present in sea water, chlorides, sulfates, carbonates, and bromides, among others.

16 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
Artur CzupryńskiArtur Czupryński
Artur Czupryński
JAJanusz Adamiec
Janusz Adamiec
Marcin AdamiakMarcin Adamiak
Marcin Adamiak
MŻMarcin Żuk
Marcin Żuk
AKAntonin Kříž
Antonin Kříž
MKMonika Kciuk
Monika Kciuk
The development trends in the energy sector clearly indicate an increase in the share of biomass and alternative fuels fed for combustion in power boilers, which results in the imposition of many unfavourable factors and a demanding working environment. During the operation of the energy system, this means a sharp increase in corrosion of the gas-tight pipe walls and coils by the destructive action of chlorine and sulphur. Implementing advanced surface protection in addition to the selection of materials of better quality and resistance to difficult working conditions would significantly reduce their wear by high temperature corrosion. Thermally sprayed coatings offer a great opportunity to protect machine components and energy systems against corrosion, erosion, impact load and abrasive wear. This article presents the test results of high-temperature corrosion resistance of coatings made with Ni-Cr-B-Si and Ni-B-Si alloy powders on a boiler steel substrate. Samples with sprayed coatings were exposed to an atmosphere with a composition of N2 + 9% O2 + 0.08% SO2 + 0.15% HCl at 800 °C for 250, 500, 750 and 1000 h. Tests results of coatings made of Ni-Cr-B-Si alloys subjected to the influence of a corrosive environment showed the formation of a layer of scale on the surface, composed mainly of Cr2O3 oxide, which was a passive layer, reducing the rate of corrosion. Coatings sprayed with Ni-B-Si alloys showed significantly lower corrosion resistance. It was found that the developed technology of subsonic flame spraying with powders of the Ni-Cr-B-Si type allows the production of coatings compliant with the requirements of the energy industry, which allows their use as anti-corrosion protection on boiler elements intended for waste disposal and biomass combustion.

1 December 2017 in Archives of Metallurgy and Materials
Verified
Journal Article
Open access
PDF file
MKMonika Kciuk
Monika Kciuk
SLS. Lasok
S. Lasok
The paper presents the influence of heat treatment on the structure and corrosion resistance of X5CrNi18-10 steel. To determine the structure which has been obtained after heat treatment the methods of light and scanning electron microscopy with EDS microanalysis were used. The electrochemical corrosion properties of the investigated steel were studied in 3.5% NaCl solution using potentiodynamic polarization tests. Basing on the registered curves, the corrosion current, polarization resistance and corrosion potential were determined. The corrosion tests were followed by fractographic researches.

1 December 2012 in Advanced Materials Research
Verified
Journal Article
Closed access
PDF file
SKSławek Kciuk
Sławek Kciuk
MKMonika Kciuk
Monika Kciuk
RTRoman Turczyn
Roman Turczyn
PMPaweł Martynowicz
Paweł Martynowicz
The main aim of the article was to present the investigation results of created megnetorheological fluids using carbonyl iron (CI) particles and analyse their behaviour in terms of the internal structure formation by a control of external magnetic field. Results of the experimental studies of a prototype magnetorheological rotary shock-absorber at various magnitudes of control current was presented in this paper.