This study investigates the mechanical properties of carbon and natural fiber-reinforced Polylactic Acid (PLA) and Polyethylene Terephthalate Glycol (PETG) composites produced via Additive Manufacturing (AM), focusing on Material Extrusion (MEX). The performance of filaments made from pre-consumer recycled PLA (rPLA) and PETG, with varying weight percentages of hemp and jute short fibers, was evaluated through tensile testing. Comparisons were made between the original filaments (PLA, carbon fiber-reinforced PLA [CF–PLA], and PETG) and their recycled versions. Multi-material compositions—neat PLA and PETG, single-graded (PLA + CF–PLA, PETG + CF–PETG), and multi-gradient (PLA + CF–PLA + PLA, PETG + CF–PETG + PETG)—were analyzed for mechanical properties. Optical microscope images of multi-material specimens were captured before and after fracture to assess failure mechanisms. The results indicate that the original CF–PETG filaments achieved a tensile strength of 50.14 MPa, which is higher than rPLA, PLA, and CF–PLA by 2%, 70%, and 6.7%, respectively. The re-manufactured PLA filaments reinforced with 7 wt% hemp fibers exhibited a tensile strength of 38.8 MPa, representing a 29% increase compared to the original PLA filaments and a 26% improvement over recycled PLA. Additionally, incorporating 7% jute fiber into PETG resulted in a tensile strength of 62.38 MPa, reflecting a 12% improvement over the original PETG filaments and a 15% increase compared to the recycled PETG filaments. Among specimens produced by AM, CF–PLA and rPLA demonstrated the highest tensile and compressive strengths. However, multi-material composites showed reduced mechanical performance compared to neat PLA and PETG, highlighting the need for improved interlayer adhesion. This study emphasizes the importance of optimizing material combinations and fiber reinforcement to enhance the mechanical properties of composites produced through AM.
Purpose: Transportation of the measurement samples from their original place to the measurement site causes significant changes in their mechanical properties. The possibility of making in situ measurements helps to create more precise discrete element models.Design/methodology/approach: The possibility of using in situ modified vane shear test based measurement for the calibration of discrete element models is demonstrated in this work.Findings: The advantage of employing the adjusted vane test is that the values of in situ measurements can be used for the calibration.Originality/value: The procedure we present allows us to perform accurate discrete element calibration using data from on-site measurements that can be performed quickly and easily.
The applicability of the typical pressure–sinkage models used to characterize the soil’s bearing properties is limited to homogeneous soils (infinite thickness) that have no hard layer. At a given depth, a hard layer can have a considerable impact on the soil’s load-bearing capacity. It is thus necessary to alter the pressure–sinkage equation by taking this condition into account when assessing the load-bearing capacity. The present paper aims to determine a simple, high-fidelity model, in terms of soil characterization, that can account for the hard layer affection. To assess hard layer affection in this paper, a plate sinkage test (bevameter) was conducted on sandy loam soil. To this end, the soil was prepared by considering three bulk densities and two soil thickness levels at 7–9% moisture content levels. According to the results, this paper put forth a new perspective and related equations for characterizing bearing performance. The sinkage modulus (k) is an intrinsic soil parameter that has a determined unit of N/cm2 and is significant for managing the bearing performance. The results showed that the new modulus sinkage model incorporates the main factor of the rigid layer effect involving high fidelity that the conventional models have failed to account for.
25 July 2018 in International Journal of Aeronautical and Space Sciences
This study intends to examine the soil behaviour in the case of finite thickness, represented by the hard layer under a soft layer of soil. A further aim is to define load-bearing capacity parameters (n and k). The experimental work is carried out under laboratory conditions by using hydraulic bevameter to apply the load. A circular plate with a diameter of 100 mm is used to push down the load over the targeted area with a penetration rate of about 9 cm/min for sinkage plates. The study was conducted in a soil bin (length of 200 cm, width of 100 cm and variable thickness) using a sandy loam soil. First, the study has been done with loose soil with a thickness of 11 cm, which maintained with 10% moisture content and initial density of 1.190 g/cm3. After that, a two thickness of 6 and 18 cm with 8% moisture content and initial soil density of 1.375 g/cm3 were tested to explain the effect of thickness. In each test, the bevameter plate was loaded at multiple locations, the result showed the soil was near uniform. The result suggests that it is not easy to obtain one equation for the load bearing capacity because the layer near to the surface behaves like soil with infinite thickness and the deeper layer like soil with finite thickness.
3 March 2019 in International Journal of Engineering and Management Sciences
The vehicle applies a normal load to the terrain, which causes sinkage and motion resistance. To forecast the normal pressure distribution on the interface of a vehicle–terrain and the tractive performance of a vehicle, the response of the terrain to normal load (which is characterized by pressure–sinkage relationship equations) must be measured. This paper presents the common conventional pressure sinkage models used in terramechanic and the modification that happened to this models. In addition the features of the new models.