WAEL MAHMOUD KHEIReldeen

Dr. WAEL MAHMOUD KHEIReldeen

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 November 2022 in Machines
Verified
Journal Article
Open access
PDF file
MAMahmoud Mohammed Atef
Mahmoud Mohammed Atef
WKWAEL MAHMOUD KHEIReldeen
WAEL MAHMOUD KHEIReldeen
JYJiwang Yan
Jiwang Yan
Mohamed G. NassefMohamed G. Nassef
Mohamed G. Nassef
The rolling element bearing is a fundamental component of any rotating machinery. During operation, wear debris and lubricant impurities create dents and bumps on the bearing raceway surfaces. Such localized defects produce transient vibration impulses at one of the bearing characteristic frequencies. Having a combination of multiple types of point defects on the raceway results in superimposed vibration patterns, which reduce the ability to recognize these defects’ effects. In this paper, a 6-DOF dynamic model is developed to accurately investigate the vibration characteristic of a ball bearing with a multipoint defect comprising a dent and bump on its raceway surface. The model considers the effects of time-varying contact force produced due to defects, lubricant film damping, bearing preload, and the inertia effect of rolling elements. The simulation results reveal the vibration behavior of multipoint defect bearings. In addition, bearing vibration response is affected by the number of defects, the angle between them, and the type and size of each defect. Furthermore, it is challenging to predict bearing defects parameters such as the numbers, types, sizes, and angles between adjacent defects from acceleration signal analysis without jerk signal analysis. The validation of the model is proved using signals from the Case Western University test setup.

2 December 2023 in Materials
Verified
Journal Article
Open access
PDF file
MAMervat Youssef Ahmed
Mervat Youssef Ahmed
EEEman Hassan El-Shenawy
Eman Hassan El-Shenawy
WKWAEL MAHMOUD KHEIReldeen
WAEL MAHMOUD KHEIReldeen
TATadaharu Adachi
Tadaharu Adachi
ANAdel Nofal
Adel Nofal
MHMohsen A. Hassan
Mohsen A. Hassan
This study aims to investigate the combined effect of niobium (Nb) microalloying and austenite grain refinement, using a specific heat treatment cycle, on the microstructure and tribological properties of Armox 500T steel. In this work, Nb addition and thermal cycling were utilized for grain refinement and enhancement of the mechanical properties of Armox 500T alloy, to provide improved protection via lightweight armor steel components with a high strength-to-weight ratio. The kinetics of transformation of the developed Armox alloys were studied using JMATPro version 13.2. The samples were subjected to two austenitizing temperatures, 1000 °C and 1100 °C, followed by 4 min of holding time and three consecutive thermal and rapid-quenching processes from 900 °C to room temperature. Scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) was employed to analyze the microstructure, which primarily consists of four types of martensite: short and long lath martensite, blocky martensite, and equiaxed martensite. Additionally, a small percentage (not exceeding 3%) of carbide precipitates was observed. The wear characteristics of the investigated alloys were evaluated using a pin-on-disc tribometer. The results demonstrate that alloying with Nb and grain refinement using a thermal cycle significantly reduce the wear rate.

20 June 2023 in Sensors
Verified
Journal Article
Open access
PDF file
MGMostafa Geriesh
Mostafa Geriesh
AEAhmed M. R. Fath El-Bab
Ahmed M. R. Fath El-Bab
WKWAEL MAHMOUD KHEIReldeen
WAEL MAHMOUD KHEIReldeen
HMHassan A. Mohamadien
Hassan A. Mohamadien
MHMohsen A. Hassan
Mohsen A. Hassan
Acceleration-based sensors are widely used in indicating the severity of damage caused to structural buildings during dynamic events. The force rate of change is of interest when investigating the effect of seismic waves on structural elements, and hence the calculation of the jerk is necessary. For most sensors, the technique used for measuring the jerk (m/s3) is based on differentiating the time–acceleration signal. However, this technique is prone to errors especially in small amplitude and low frequency signals, and is deemed not suitable when online feedback is required. Here, we show that direct measurement of the jerk can be achieved using a metal cantilever and a gyroscope. In addition, we focus on the development of the jerk sensor for seismic vibrations. The adopted methodology optimized the dimensions of an austenitic stainless steel cantilever and enhanced the performance in terms of sensitivity and the jerk measurable range. We found, after several analytical and FE analyses, that an L-35 cantilever model with dimensions 35 × 20 × 0.5 (mm3) and a natural frequency of 139 (Hz) has a remarkable performance for seismic measurements. Our theoretical and experimental results show that the L-35 jerk sensor has a constant sensitivity value of 0.05 ((deg/s)/(G/s)) with ±2% error in the seismic frequency bandwidth of 0.1~40 (Hz) and for amplitudes in between 0.1 and 2 (G). Furthermore, the theoretical and experimental calibration curves show linear trends with a high correlation factor of 0.99 and 0.98, respectively. These findings demonstrate the enhanced sensitivity of the jerk sensor, which surpasses previously reported sensitivities in the literature.



23 July 2024 in Journal of Nano Research
Verified
Journal Article
Closed access
PDF file
AIAbubakar Ibrahim
Abubakar Ibrahim
UEUsama Mohamed Nour Eldemerdash
Usama Mohamed Nour Eldemerdash
TYTsuyoshi Yoshitake
Tsuyoshi Yoshitake
WKWAEL MAHMOUD KHEIReldeen
WAEL MAHMOUD KHEIReldeen
Marwa ElkadyMarwa Elkady
Marwa Elkady
This study employed an innovative approach, utilizing prepared dried polyurethane-polyaniline nano-composite, through in-situ polymerization, for continuous remediation of Congo red dye. Response Surface Methodology (RSM) based on the Box-Behnken design (BBD) model was utilized to optimize the processing parameters, including initial dye concentration, flow rate, and pH. The two-factor interaction (2FI) model emerged as the most significant, highlighting the influence of individual and interaction effects of the factors. Optimization of the dye remediation process yielded the optimal conditions of a flow rate of 10 mL/min, acidic pH of 5.00, and dye concentration of 20 mg/L, resulting in an impressive, predicted removal efficiency of 99.09% agreeing with the experimental value. Moreover, the maximum adsorption capacity was determined to be 329.68 mg/g. Characterization of the adsorbent material involved techniques such as Scanning electron microscopy (SEM), Fourier transforms infrared spectra (FTIR), X-ray spectroscopy (XRD), and Zeta potential analysis. This material offers a sustainable alternative in industries to treat Congo red dye before being disposed of into the environment.