Linghui Kong

Dr. Linghui Kong


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 August 2024 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
QZQi Zheng
Qi Zheng
WLWenxuan Liu
Wenxuan Liu
QZQi Zhao
Qi Zhao
LKLinghui Kong
Linghui Kong
YRYuhui Ren
Yuhui Ren
XYXue-xia Yang
Xue-xia Yang
A metasurface (MS)-based low-profile, low radar cross section (RCS), wideband, and miniaturized microstrip patch array is proposed in this paper. First, a new method by combining reactive impedance surface and polarization conversion metasurface for antenna miniaturization and bandwidth enhancement as well as broadband RCS reduction is proposed. The proposed antenna is composed of a conventional patch antenna on top of an MS-based substrate. For the radiation performance, the antenna has a 10-dB impedance matching band of 22.3% and the overall volume is reduced to 78.9% after using the MS. For the scattering performance, broadband RCS reduction is achieved due to the polarization conversion characteristic of the MS. Over 10-dB RCS reduction is obtained from 6.10 to 18.90 GHz (a relative bandwidth of 106%). Second, the array composed of the 4×4 element antennas and a feeding network is constructed and discussed. A 25.6% 10-dB impedance matching bandwidth and 106% 6-dB RCS reduction bandwidth are obtained. The overall size of the proposed array is reduced to 76% compared to the array without the MS. A prototype of the array was fabricated and measured. The measured results and the simulated ones are in good agreement. The proposed array by combining reactive impedance surface and polarization conversion metasurface has the advantages of wideband, miniaturized size, low RCS, and low-profile, which can be used for radar, aircraft, and stealth platforms.

14 March 2022 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
XHXingli He
Xingli He
KCKai Chen
Kai Chen
LKLinghui Kong
Linghui Kong
PLPeng Li
Peng Li
This work demonstrates super-high frequency wave-guided surface acoustic wave (SAW) devices based on LiNbO3/SiO2/Si layered substrates. SAW resonators with fundamental operating frequency to the 7-GHz range were developed, and wave modes like the Rayleigh, Shear-horizontal (SH), Pseudo-Bulk, etc., were observed. Furthermore, effective coupling coefficients (k2eff) and quality factor (Q) of the devices have been investigated systematically. Specifically, spurious-free SAW resonators with the SH wave frequency over 7.40 GHz and the high k2eff value of ∼7.8% were obtained at a nanoscale wavelength of 480 nm. Finally, high-performance filters with a bandwidth over 300 MHz were achieved. The demonstrated filters show sharp roll-off and spurious-free responses within the passband with insertion loss <−5 dB and a small temperature coefficient of frequency of ∼−45.8 ppm/K at a super-high frequency of 7.17 GHz. Upon further optimizations, high-performance SAW devices built on a single crystalline LiNbO3 film can potentially enable the low-loss and wideband signal processing functions, promising for the next-generation radio frequency front-end system applications.

30 November 2021 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
XHXingli He
Xingli He
JZJian Zhou
Jian Zhou
WXWeipeng Xuan
Weipeng Xuan
ZZZhengjia Zhan
Zhengjia Zhan
YZYunjing Zhang
Yunjing Zhang
LKLinghui Kong
Linghui Kong
Ultrahigh-frequency surface acoustic wave (SAW) devices with high quality ( $Q$ ) factors are essential components for the next-generation wireless communication system. In this work, we reported high-performance and ultrahigh-frequency SAW devices with single-crystalline LiTaO 3 /SiO 2 /Si [LT-on-insulator (LTOI)] multilayered heterostructure. The fabricated SAW resonators exhibited multi-resonant modes (Rayleigh, Sezawa, and LLSAW mode) with the frequency ranging from 1.81 to 8.33 GHz. Especially, the SAW resonator with the Rayleigh wave frequency over 5.0 GHz and high $Q$ value around 2300 with a wavelength of 600 nm was realized. The variation of the phase velocity, the $Q$ factor for each resonant mode, and the effective coupling coefficients ( $k^{2}_{\mathrm {eff}}$ ) versus the normalized LiTaO 3 film thickness were systematically investigated. The proposed high-frequency SAW based on LTOI multilayered heterostructure possesses the low temperature coefficient of frequency (TCF, −20 ppm/K). Furthermore, a high-performance SAW bandpass filter with the center frequency of ~3.5 GHz was achieved. The work shows the great potential of the LiTaO 3 single-crystalline thin-films-based SAW for ultrahigh frequency electronics applications.

15 June 2018 in Microwave and Optical Technology Letters
Verified
Journal Article
Closed access
PDF file
LKLinghui Kong
Linghui Kong
Sen YANSen YAN
Sen YAN
GVGuy A. E. Vandenbosch
Guy A. E. Vandenbosch

13 November 2023 in Applied Physics Letters
Verified
Journal Article
Open access
PDF file
JSJunjie Shen
Junjie Shen
HCHaibo Chen
Haibo Chen
ZSZimeng Shi
Zimeng Shi
LKLinghui Kong
Linghui Kong
YZYunjing Zhang
Yunjing Zhang
XHXingli He
Xingli He
Surface acoustic wave (SAW) devices are promising for chemical and biological sensing applications. This work studies the basic operating principles and the physical behaviors of the “Rayleigh”-SAW and the “Shear Horizontal (SH-)” bulk acoustic wave (BAW), particularly in relation to the chemisorption process. A complete 3D delay line SAW model is developed and performed by the finite element analysis, and a methodology was introduced for characterizing the transmission characteristics (S21) of these devices. Notably, our investigation unveils an intriguing phenomenon in the behavior of SH-BAW in response to loading mass. We observed an anomalous shift in the central frequency, which increases as the chemical adsorbate concentration rises. Leveraging these insights, we designed and constructed a SAW-based gas sensor, and the vinyl-terminated polydimethylsiloxane was synthesized for the detection of chloroform, a challenging pollutant to identify. Through a comparative study, we illustrate distinct responses of Rayleigh-SAW and SH-BAW devices to accumulated loading mass and gaseous contaminants. These experimental results validate and corroborate our simulations. This work demonstrates a unique mass-loading effect exhibited by SH-BAW devices, which differs from the existing theories. These findings offer the opportunity to refine and enhance models for accurately describing the functionality of delay line SAW sensors, thereby contributing to improved sensor reliability.

8 March 2018 in Microwave and Optical Technology Letters
Verified
Journal Article
Closed access
PDF file
LKLinghui Kong
Linghui Kong
SYSen Yan
Sen Yan
VVVladimir Volski
Vladimir Volski
GVGuy A. E. Vandenbosch
Guy A. E. Vandenbosch