Denisa-Iulia Brus

Ms. Denisa-Iulia Brus

Transilavania University of Brasov
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 December 2021 in Polymers
Verified
Journal Article
Open access
PDF file
DCDorin-Ioan Catana
Dorin-Ioan Catana
MPMihai Alin Pop
Mihai Alin Pop
DBDenisa-Iulia Brus
Denisa-Iulia Brus
Additive manufacturing is one of the technologies that is beginning to be used in new fields of parts production, but it is also a technology that is constantly evolving, due to the advances made by researchers and printing equipment. The paper presents how, by using the simulation process, the geometry of the 3D printed structures from PLA and PLA-Glass was optimized at the bending stress. The optimization aimed to reduce the consumption of filament (material) simultaneously with an increase in the bending resistance. In addition, this paper demonstrates that the simulation process can only be applied with good results to 3D printed structures when their mechanical properties are known. The inconsistency of printing process parameters makes the 3D printed structures not homogeneous and, consequently, the occurrence of errors between the test results and those of simulations become natural and acceptable. The mechanical properties depend on the values of the printing process parameters and the printing equipment because, in the case of 3D printing, it is necessary for each combination of parameters to determine their mechanical properties through specific tests.

1 June 2021 in Molecules
Verified
Journal Article
Open access
PDF file
DCDorin-Ioan Catana
Dorin-Ioan Catana
MPMihai Alin Pop
Mihai Alin Pop
DBDenisa-Iulia Brus
Denisa-Iulia Brus
The additive manufacturing process is one of the technical domains that has had a sustained development in recent decades. The designers’ attention to equipment and materials for 3D printing has been focused on this type of process. The paper presents a comparison between the results of the bending tests and those of the simulation of the same type of stress applied on 3D-printed PLA and PLA–glass structures. The comparison of the results shows that they are close, and the simulation process can be applied with confidence for the streamline of filament consumption, with direct consequences on the volume and weight of additive manufactured structures. The paper determines whether the theories and concepts valid in the strength of materials can be applied to the additive manufacturing pieces. Thus, the study shows that the geometry of the cross-section, by its shape (circular or elliptical) and type (solid or ring shaped), influences the strength properties of 3D-printed structures. The use of simulation will allow a significant shortening of the design time of the new structures. Moreover, the simulation process was applied with good results on 3D-printed structures in which two types of filaments were used for a single piece (structure).

22 August 2025 in Polymers
Verified
Journal Article
Open access
PDF file
DCDorin-Ioan Catana
Dorin-Ioan Catana
DBDenisa-Iulia Brus
Denisa-Iulia Brus
MPMihai Alin Pop
Mihai Alin Pop
MAMihai Alexandru Alexandru
Mihai Alexandru Alexandru
Additive manufacturing is a relatively new and modern technological process that is still under development and progress, with a wide range of materials. This study presents the evolution of the mechanical properties of poly (lactic acid) depending on the main parameters of additive manufacturing: speed, infill density, and temperature. In this study, the range considered for each parameter is the one commonly used in printing activities. The study shows that within the analysed range, the relationship between the property values and printing temperature is expressed through third-degree polynomial equations, regardless of the infill density. This study also presents the evolution of the properties as a function of two printing parameters, specifically temperature and infill density. Through statistical analysis, equations were determined that describe the relationship between the studied properties and the printing parameters. The existence of these equations facilitates their integration into commonly used simulation programs for design. Additionally, this study presents the results of the simulation process for tensile tests on additively manufactured structures, based on data obtained from tensile tests. The simulation results show that the outcomes align with those from the tests, and the identified errors can be kept under control.

28 November 2023 in Revista Romaneasca pentru Educatie Multidimensionala
Verified
Journal Article
Open access
PDF file
RERazvan Sandu Enoiu
Razvan Sandu Enoiu
DBDenisa-Iulia Brus
Denisa-Iulia Brus
VMVeronica Ghergut Mîndrescu
Veronica Ghergut Mîndrescu
The study explains how employing sensors while alpine skiing may raise an athlete's technical proficiency. The sensors offer a reliable set of data that enables the creation of a picture of the athlete's technical dexterity. Through statistical analysis of this data, it is possible to derive the equation for multiple linear regression, which illustrates the relationship between the athlete's time recording (which is regarded as the dependent variable) and the sensor-monitored parameters (considered independent variables). In the study, two linear regression equations were developed, with the number of independent variables considered determining which one was used. The quantity of athletes being watched and their technical proficiency have an impact on how accurate multiple linear regression is. The educational utility of the study derives from the mathematical model provided. This model will enable the athlete to concentrate primarily on the technical aspects of performance improvement while also understanding how improvement in specific technical elements affects the potential time to be achieved.

15 December 2020 in Scientific Bulletin of Naval Academy
Verified
Journal Article
Closed access
DBDenisa-Iulia Brus
Denisa-Iulia Brus
The purpose of this research is to signal the importance of mental training which consists in developing those aspects of the athlete's psycho-behavioral activity that condition him an effective conduct in training both in terms of full adaptation to stress and stress, and in terms of technical and tactical perfection. In this sense, we start from the premise that psychological monitoring in performance sports in general and in alpine skiing in general through objective investigations and evaluations, determine the achievement of superior results both in the training of athletes and in competition

7 March 2026 in Sensors
Verified
Journal Article
Open access
PDF file
DBDenisa-Iulia Brus
Denisa-Iulia Brus
RERazvan Sandu Enoiu
Razvan Sandu Enoiu
DCDorin-Ioan Catana
Dorin-Ioan Catana
Breaststroke performance is highly dependent on lower-limb biomechanics and the coordination of movement during the kick cycle. Recent advances in wearable inertial sensor technology enable objective analysis of human motion in real training environments. This study presents an exploratory pilot investigation aimed at evaluating the feasibility of using wearable inertial sensors for biomechanical analysis of the breaststroke kick in young swimmers. Five male children (aged 8–10 years) with basic breaststroke proficiency participated in a single-group pre–post exploratory study conducted over a three-month period. Lower-limb motion was monitored using wearable inertial measurement units attached bilaterally to the shanks and feet, allowing real-time kinematic feedback and data recording during training sessions. The intervention consisted of five structured training sessions integrating drill-based breaststroke kick exercises with sensor-assisted feedback. Outcome measures included time-based swimming performance tests (40 m breaststroke kick with kickboard and 40 m breaststroke without kickboard) and qualitative biomechanical evaluations of the passive and active phases of the breaststroke kick. Additionally, selected IMU-derived kinematic variables (peak ankle dorsiflexion and external foot rotation angles) were analyzed to provide quantitative biomechanical insight. Following the intervention, improvements were observed across all outcome measures, including reduced swimming times and increased technique scores assigned by two independent evaluators. These findings support the feasibility of integrating wearable IMUs for technique monitoring and simple kinematic quantification of breaststroke kick mechanics in young swimmers; larger controlled studies are required to assess efficacy.