Dorin-Ioan Catana

Prof. Dr. Dorin-Ioan Catana

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 February 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MIMilosan Ioan
Milosan Ioan
TBTibor Bedo
Tibor Bedo
CGCamelia Gabor
Camelia Gabor
Daniel MunteanuDaniel Munteanu
Daniel Munteanu
MPMihai Alin Pop
Mihai Alin Pop
BVBéla Varga
Béla Varga
The continuous development of modern industries rises the necessity for functionally graded materials. This research starts from the consideration that the incorporation of SiC particles in the molten aluminum alloy can be difficult due to the very low wettability of SiC particles. In order to increase their wettability, SiC particles were covered with a layer of metallic copper. The incorporation of SiC particles into the aluminum alloy mass was performed by centrifugal casting. The secondary hypoeutectic Al-Si alloy used in this study was elaborated within the crucible of a resistors heated furnace. The metallic coating of SiC particles, in addition to the effect of increasing their wettability by molten metal, also has a role in preventing the formation of aluminum carbide in case of heating above 700 °C. A great amount of attention was paid to the parameters used during the centrifugal casting process. The results showed that adjusting the proportion of SiC particles within the composite allows us to obtain values of the thermal expansion coefficient within previously established limits. The present work demonstrates that the coating of SiC particles covered with a thin layer of metallic Cu creates the conditions to easily incorporate them into the molten Al mass, thus obtaining FGMs with controlled properties.

14 December 2021 in Polymers
Verified
Journal Article
Open access
PDF file
DCDorin-Ioan Catana
Dorin-Ioan Catana
MPMihai Alin Pop
Mihai Alin Pop
DBDenisa-Iulia Brus
Denisa-Iulia Brus
Additive manufacturing is one of the technologies that is beginning to be used in new fields of parts production, but it is also a technology that is constantly evolving, due to the advances made by researchers and printing equipment. The paper presents how, by using the simulation process, the geometry of the 3D printed structures from PLA and PLA-Glass was optimized at the bending stress. The optimization aimed to reduce the consumption of filament (material) simultaneously with an increase in the bending resistance. In addition, this paper demonstrates that the simulation process can only be applied with good results to 3D printed structures when their mechanical properties are known. The inconsistency of printing process parameters makes the 3D printed structures not homogeneous and, consequently, the occurrence of errors between the test results and those of simulations become natural and acceptable. The mechanical properties depend on the values of the printing process parameters and the printing equipment because, in the case of 3D printing, it is necessary for each combination of parameters to determine their mechanical properties through specific tests.

1 June 2021 in Molecules
Verified
Journal Article
Open access
PDF file
DCDorin-Ioan Catana
Dorin-Ioan Catana
MPMihai Alin Pop
Mihai Alin Pop
DBDenisa-Iulia Brus
Denisa-Iulia Brus
The additive manufacturing process is one of the technical domains that has had a sustained development in recent decades. The designers’ attention to equipment and materials for 3D printing has been focused on this type of process. The paper presents a comparison between the results of the bending tests and those of the simulation of the same type of stress applied on 3D-printed PLA and PLA–glass structures. The comparison of the results shows that they are close, and the simulation process can be applied with confidence for the streamline of filament consumption, with direct consequences on the volume and weight of additive manufactured structures. The paper determines whether the theories and concepts valid in the strength of materials can be applied to the additive manufacturing pieces. Thus, the study shows that the geometry of the cross-section, by its shape (circular or elliptical) and type (solid or ring shaped), influences the strength properties of 3D-printed structures. The use of simulation will allow a significant shortening of the design time of the new structures. Moreover, the simulation process was applied with good results on 3D-printed structures in which two types of filaments were used for a single piece (structure).

19 July 2019 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Closed access
PDF file
DCDorin-Ioan Catana
Dorin-Ioan Catana
JRJose Rodriguez
Jose Rodriguez
Inmaculada CañadasInmaculada Cañadas
Inmaculada Cañadas
MIMilosan Ioan
Milosan Ioan

7 October 2020 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
DCDorin-Ioan Catana
Dorin-Ioan Catana
MPMihai‐Alin Pop
Mihai‐Alin Pop

22 August 2025 in Polymers
Verified
Journal Article
Open access
PDF file
DCDorin-Ioan Catana
Dorin-Ioan Catana
DBDenisa-Iulia Brus
Denisa-Iulia Brus
MPMihai Alin Pop
Mihai Alin Pop
MAMihai Alexandru Alexandru
Mihai Alexandru Alexandru
Additive manufacturing is a relatively new and modern technological process that is still under development and progress, with a wide range of materials. This study presents the evolution of the mechanical properties of poly (lactic acid) depending on the main parameters of additive manufacturing: speed, infill density, and temperature. In this study, the range considered for each parameter is the one commonly used in printing activities. The study shows that within the analysed range, the relationship between the property values and printing temperature is expressed through third-degree polynomial equations, regardless of the infill density. This study also presents the evolution of the properties as a function of two printing parameters, specifically temperature and infill density. Through statistical analysis, equations were determined that describe the relationship between the studied properties and the printing parameters. The existence of these equations facilitates their integration into commonly used simulation programs for design. Additionally, this study presents the results of the simulation process for tensile tests on additively manufactured structures, based on data obtained from tensile tests. The simulation results show that the outcomes align with those from the tests, and the identified errors can be kept under control.