Mihai Alexandru Alexandru

Dr. Mihai Alexandru Alexandru

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 June 2024 in Materials
Verified
Journal Article
Open access
PDF file
MAMihai Alexandru Alexandru
Mihai Alexandru Alexandru
IRIonuţ Claudiu Roatǎ
Ionuţ Claudiu Roatǎ
Catalin CroitoruCatalin Croitoru
Catalin Croitoru
ATAlina Luciana Todi-Eftimie
Alina Luciana Todi-Eftimie
This study advances the vibration-assisted welding (VAW) technique for joining medium-carbon, low-alloy steels, which are typically challenging to weld. Traditional welding methods suggest low linear energy and mandatory pre- and post-heating due to these steels’ poor weldability. However, VAW employs a vibrating table to maintain part vibration throughout the automatic MIG/MAG welding process. This study tested the VAW technique on 42CrMo4 steel samples, achieving satisfactory weld quality without the need for pre- and post-heating treatments. This research revealed that while vibration frequencies between 550 Hz and 9.5 kHz minimally affect the appearance of the weld joint, the oscillation acceleration has a significant impact. The acceleration along the weld axis (ax), combined with the welding speed and vibration frequency, affects the weld surface’s appearance, particularly its scaly texture and size. Lateral acceleration (ay) alters the seam width, whereas vertical acceleration (az) affects penetration depth at the root. Notably, if the effective acceleration (aef) surpasses 40 m/s2, there is a risk of molten metal expulsion from the weld pool or piercing at the joint’s base. The quality of the joints was assessed through macroscopic and microscopic structural analyses, micro-hardness tests in the weld zone, and bending trials. The mechanical properties of the VAW samples were found to be acceptable, with hardness slightly exceeding that of the samples subjected to pre- and post-heating. Moreover, the VAW process significantly reduced energy consumption and operational time. The employed vibration system, with a power rating of 100 W, operates for just a few minutes, resulting in substantially lower energy usage compared to the traditional pre- and post-heating method, which typically requires a 5 kW electric furnace.

22 August 2025 in Polymers
Verified
Journal Article
Open access
PDF file
DCDorin-Ioan Catana
Dorin-Ioan Catana
DBDenisa-Iulia Brus
Denisa-Iulia Brus
MPMihai Alin Pop
Mihai Alin Pop
MAMihai Alexandru Alexandru
Mihai Alexandru Alexandru
Additive manufacturing is a relatively new and modern technological process that is still under development and progress, with a wide range of materials. This study presents the evolution of the mechanical properties of poly (lactic acid) depending on the main parameters of additive manufacturing: speed, infill density, and temperature. In this study, the range considered for each parameter is the one commonly used in printing activities. The study shows that within the analysed range, the relationship between the property values and printing temperature is expressed through third-degree polynomial equations, regardless of the infill density. This study also presents the evolution of the properties as a function of two printing parameters, specifically temperature and infill density. Through statistical analysis, equations were determined that describe the relationship between the studied properties and the printing parameters. The existence of these equations facilitates their integration into commonly used simulation programs for design. Additionally, this study presents the results of the simulation process for tensile tests on additively manufactured structures, based on data obtained from tensile tests. The simulation results show that the outcomes align with those from the tests, and the identified errors can be kept under control.

5 December 2019 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Closed access
PDF file
MAMihai Alexandru Alexandru
Mihai Alexandru Alexandru
Mircea Horia TIEREANMircea Horia TIEREAN
Mircea Horia TIEREAN
TPTeodor Machedon Pisu
Teodor Machedon Pisu
JRJose Rodriguez
Jose Rodriguez
Catalin CroitoruCatalin Croitoru
Catalin Croitoru

9 October 2026 in International Journal of Metalcasting
Verified
Journal Article
Open access
PDF file
MAMihai Alexandru Alexandru
Mihai Alexandru Alexandru
Mircea Horia TIEREANMircea Horia TIEREAN
Mircea Horia TIEREAN
The paper highlights the natural relaxation of internal stresses in cast iron by analyzing the changes in the longitudinal modulus of elasticity and the logarithmic decrement that occurred over 50 years, under conditions in which the samples were not subjected to mechanical stress during this period. The evaluation of elastic properties was carried out by analyzing the resonance curves of the samples subjected to forced bending oscillations. It is found that, over time, discrete changes in the dynamic response of cast iron occur, which can be identified by resonance-based measurements. In all samples, an average increase in the longitudinal modulus of elasticity, ΔE med = +3.55% within the limits of 2-5.94% was found. The logarithmic decrement, respectively, the internal friction, decreased, on average, by Δδ med = −7.15% within the limits of 1.98−11.43%. These findings lead to the conclusion that, over time, in cast irons that have not undergone a stress-relief heat treatment, processes occur that are part of the dissipation of internal energy in the material. The spontaneous relaxation of internal stresses is associated with slow time-dependent processes that modify the elastic and damping behavior of the material and can be detected through changes in its dynamic properties.

MAMihai Alexandru Alexandru
Mihai Alexandru Alexandru
DCDorin-Ioan Catana
Dorin-Ioan Catana
DMDana Luca Motoc
Dana Luca Motoc
Mircea Horia TIEREANMircea Horia TIEREAN
Mircea Horia TIEREAN
Hot extrusion tools operate under severe thermal and mechanical conditions, which significantly limit their service life. During operation, the punch and die absorb large amounts of heat from the hot billet while being subjected to high pressures and intense friction, leading to severe abrasive wear and progressive hardness reduction. In practice, the punch generally exhibits a shorter service life than the die. The present study proposes a technological solution for reconditioning worn extrusion punches using vibration-assisted welding (VAW). A wear-resistant layer was deposited by MIG welding using DUR 600 filler material, while mechanical vibrations were introduced through a vibrating welding table. The applied vibration regime consisted of a frequency of 50 Hz–108 Hz and acceleration components of ax = 30–60 m/s2 and az = 35–70 m/s2. The experimental investigations included macroscopic analysis, hardness and microhardness measurements, microstructural observations, and SEM-EDS line scanning analysis of the dilution zone between the cladding material and the base metal. The results suggest that vibration-assisted welding may influence the microstructural characteristics, hardness distribution, and dilution behavior of the cladded layer. The vibrated specimens exhibited higher hardness values in the range of 702 to 908 HV5–10. Under the investigated conditions, the process did not require additional hardening treatment, and only a stress-relief annealing stage was applied. The proposed VAW approach appears to be a promising option for the reconditioning of hot extrusion tools; however, further investigations are required to validate its performance under industrial conditions.

25 September 2026 in Vehicles
Verified
Journal Article
Open access
PDF file
BNBogdan Ioan Nituleasa
Bogdan Ioan Nituleasa
Camelia CerbuCamelia Cerbu
Camelia Cerbu
HTHoratiu Teodorescu-Draghicescu
Horatiu Teodorescu-Draghicescu
MAMihai Alexandru Alexandru
Mihai Alexandru Alexandru
DMDana Luca Motoc
Dana Luca Motoc
This study explores the quasi-static and dynamic responses of irregular, honeycomb-like topologies made from glycol polyethylene terephthalate (PETG) with various sparse infill densities, using fused filament fabrication (FFF) manufacturing technology. Both tensile and flexural tests revealed a linear increase in Young’s modulus and sample strength as infill density increased, under constant printing and testing conditions. Below 50% infill, this trend remained unchanged, despite cells being irregular and fracture mechanics differing. Low-velocity impact tests were conducted at a velocity of 1.5 m/s, equivalent to an incident energy of 6.2 J. Regarding dynamic responses, irregular honeycomb-like structures use 12.5–25% of the nominal pendulum energy during complete fracture in Charpy tests, and 74.3–98.3% of total available energy during low-impact crushing. Samples with infill densities of 15% and 25% revealed higher absorbed energy values of around 6.5 and 6.1 J, respectively, compared with denser samples. Although they exhibit more favorable mass-specific energy absorption, these samples collapse more quickly than their stiffer 50–100% counterparts. The findings provide valuable insights into irregular, honeycomb-like structures and open up perspectives for optimization and component-level assessment, with potential applications as impact-resistant, secondary/non-structural components for the automotive industry.