Unconfined compressive strength (UCS) is an important rock parameter required in the engineering design of structures built on top or within the interior of rock formations. In a site investigation project, UCS is typically obtained discretely (through point-to-point measurement) and interpolated. This method is less than optimal to resolve meter-scale UCS variations of heterogenous rock such as carbonate formations in which property changes occur within data spacing. We investigate the geotechnical application of multiattribute analysis based on near-surface reflection seismic data to probe rock formations for their strength attributes at meter-scale variability. Two Late Jurassic outcrops located in central Saudi Arabia serve as testing sites: the Hanifa Formation in Wadi Birk and the Jubaila Formation in Wadi Laban. The study uses core and 2D seismic profiles acquired in both sites, from which we constrain UCS, acoustic velocity, density, and gamma-ray values. A positive linear correlation between UCS and acoustic impedance along the core indicates that seismic attributes can be utilized as a method to laterally extrapolate the UCS away from the core location. Seismic colored inversion serves as input for neural network multiattribute analysis and is validated with a blind test. Results from data at both outcrop sites indicate a high degree of consistency with an absolute UCS error of approximately 5%. We also demonstrate the applicability of predicted UCS profiles to interpret mechanical stratigraphy and map lateral UCS heterogeneities. These findings provide a less expensive alternative to constrain UCS from limited core data on a field-scale site engineering project.
Pore casting refers to filling the void spaces of porous materials with an extraneous fluid, usually epoxy resin, to obtain a high-strength composite material, stabilize a fragile porous structure, produce a three-dimensional replica of the pore space, or provide imaging contrast. Epoxy pore casting may be accompanied by additional procedures, such as etching, in which the material matrix is dissolved, leaving a clean cast. Moreover, an epoxy resin may be mixed with fluorophore substances to allow fluorescence imaging. Our work aims to investigate and optimize the epoxy pore casting procedure parameters, for example, impregnation pressure. We use silicon micromodels as a reference to validate the key parameters of high-pressure resin impregnation. We demonstrate possible artifacts and defects that might develop during impregnation with resin, e.g., resin shrinkage and gas trapping. In the end, we developed an optimized protocol to produce high-quality resin pore casts for high-resolution 3D imaging and the description of microporosity in micritic carbonates. In our applications, the high-quality pore casts were acid-etched to remove the non-transparent carbonate material, making the pore casts suitable for imaging with Confocal Laser Scanning Microscopy (CLSM). In addition, we evaluate the quality of our etching procedure using micro-computed tomography (micro-CT) scans of the pre- and post-etched samples and demonstrate that the etched epoxy pore casts represent the pore space of microporous carbonate rock samples with high fidelity.
Tepee structures are upward‐buckling fracture rims that form a reticulated network of polygonal boundaries when viewed from an aerial perspective. These structures are thought to result from crystallisation forces of cement, causing lateral expansion of consolidating sedimentary materials. Tepee structures are indicative of subaerial exposure and can serve as stratigraphic markers in ancient carbonate sequences. While tepee structures are common in ancient carbonate sequences, in modern settings, they have only been described in the Arabian Gulf. The discovery of fields of polygonal structures, on satellite images of the Red Sea Island of Sheybarah, Saudi Arabia, motivated the authors to assess their genesis and distribution in Arabia. The objectives are to describe in detail tepees and their arrangement in polygonal patterns, investigate the timing of their formation and constrain the relative timing of tepee generation. Furthermore, this study investigates, based on a detailed satellite image survey, whether similar polygonal features can be identified around the Arabian Peninsula. The polygonal crusts on Sheybarah Island are found in intertidal to supratidal settings overlying a well‐lithified ravinement surface. They are composed of locally derived poorly sorted sand‐to‐pebble‐sized coral, mollusc and foraminifera debris of predominantly aragonite and high Mg‐calcite mineralogy with minor admixtures of siliciclastics. Based on petrographic analysis, microbial‐induced cement precipitation is the major lithification agent. Lithification occurs in the upper intertidal zone based on the ubiquitous presence of keystone vugs. Radiocarbon ( 14 C) dates reveal elevation‐aligned ages between approximately 1.5 and 3.0 ka BP, allowing the reconstruction of late Holocene minor sea‐level changes aligned with major global climate variations. Hence, polygonal tepee structures may serve as proxies for sea‐level changes. Of 126 occurrences of polygonal fields identified from satellite images, 89 in the Red Sea are probably composed of polygonal reefs. The authors hypothesise that polygonal coral reefs originated on tepee crust.