Weidong Fang

Dr. Weidong Fang


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 March 2021 in Sensors
Verified
Journal Article
Open access
PDF file
YYYuan Yao
Yuan Yao
DPDebin Pan
Debin Pan
JWJianbo Wang
Jianbo Wang
TDTingting Dong
Tingting Dong
JGJie Guo
Jie Guo
QLQianbo Lu
Qianbo Lu
The Micro-Opto-Electro-Mechanical Systems (MOEMS) accelerometer is a new type of accelerometer that combines the merits of optical measurement and Micro-Electro-Mechanical Systems (MEMS) to enable high precision, small volume, and anti-electromagnetism disturbance measurement of acceleration, which makes it a promising candidate for inertial navigation and seismic monitoring. This paper proposes a modified micro-grating-based accelerometer and introduces a new design method to characterize the grating interferometer. A MEMS sensor chip with high sensitivity was designed and fabricated, and the processing circuit was modified. The micro-grating interference measurement system was modeled, and the response sensitivity was analyzed. The accelerometer was then built and benchmarked with a commercial seismometer in detail. Compared to the previous prototype in the experiment, the results indicate that the noise floor has an ultra-low self-noise of 15 ng/Hz1/2.

4 December 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
JCJiaxiao Chen
Jiaxiao Chen
QLQianbo Lu
Qianbo Lu
Jian BaiJian Bai
Jian Bai
XXXiang Xu
Xiang Xu
YYYuan Yao
Yuan Yao
WFWeidong Fang
Weidong Fang
External temperature changes can detrimentally affect the properties of a microaccelerometer, especially for high-precision accelerometers. Temperature control is the fundamental method to reduce the thermal effect on microaccelerometer chips, although high-performance control has remained elusive using the conventional proportional-integral-derivative (PID) control method. This paper proposes a modified approach based on a genetic algorithm and fuzzy PID, which yields a profound improvement compared with the typical PID method. A sandwiched microaccelerometer chip with a measurement resistor and a heating resistor on the substrate serves as the hardware object, and the transfer function is identified by a self-built measurement system. The initial parameters of the modified PID are obtained through the genetic algorithm, whereas a fuzzy strategy is implemented to enable real-time adjustment. According to the simulation results, the proposed temperature control method has the advantages of a fast response, short settling time, small overshoot, small steady-state error, and strong robustness. It outperforms the normal PID method and previously reported counterparts. This design method as well as the approach can be of practical use and applied to chip-level package structures.

22 July 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
HHHaoyu Huang
Haoyu Huang
WFWeidong Fang
Weidong Fang
CWChen Wang
Chen Wang
Jian BaiJian Bai
Jian Bai
Kaiwei WangKaiwei Wang
Kaiwei Wang
QLQianbo Lu
Qianbo Lu
Bandwidth is an important parameter for accelerometers, in some cases, even surpassing sensitivity. However, there are few studies focused on the relationship between bandwidth and environmental conditions in practical application of accelerometers. In this paper, we systematically analyze the influence of environment on the bandwidth of accelerometers, obtaining the amplitude–frequency response curves versus damping ratio and properties of materials, wherein temperature and humidity were found as the two dominant factors that influence the bandwidth of accelerometers. Common temperature and humidity variations can result in bandwidth degradation of about 25% according to our theoretical analysis. The finite element method (FEM) is introduced to verify our theoretical analysis, and the accordance of the FEM simulation results and the theoretical results confirmed the validity of our analysis. Furthermore, a modification design is proposed to compensate for the influence of temperature and humidity on the bandwidth of accelerometers. By choosing materials with an appropriate Young’s modulus and coefficient of thermal expansion, the degradation of the bandwidth was substantially diminished by more than one order of magnitude, which can serve as a strong guide for the future realization of accelerometers with a steady and large bandwidth.

15 December 2022 in Sensors
Verified
Journal Article
Open access
PDF file
XXXiang Xu
Xiang Xu
SWShuang Wu
Shuang Wu
WFWeidong Fang
Weidong Fang
ZYZhe Yu
Zhe Yu
ZJZeyu Jia
Zeyu Jia
QLQianbo Lu
Qianbo Lu
There is a constraint between the dynamic range and the bandwidth of MEMS accelerometers. When the input acceleration is comparatively large, the squeeze film damping will increase dramatically with the increase in the oscillation amplitude, resulting in a decrease in bandwidth. Conventional models still lack a complete vibration response analysis in large amplitude ratios and cannot offer a suitable guide in the optimization of such devices. In this paper, the vibration response analysis of the sensing unit of an accelerometer in large amplitude ratios is first completed. Then, the optimal design of the sensing unit is proposed to solve the contradiction between the dynamic range and the bandwidth of the accelerometer. Finally, the results of the vibration experiment prove that the maximum bandwidth can be achieved with 0~10g external acceleration, which shows the effectiveness of the design guide. The new vibration analysis with the complete model of squeeze film damping is applicable to all sensitive structures based on vibration, not limited to the MEMS accelerometer studied in this thesis. The bandwidth optimal scheme also provides a strong reference for similar structures with large oscillation amplitude ratios.

8 February 2022 in IEEE Sensors Journal
Verified
Journal Article
Closed access
WFWeidong Fang
Weidong Fang
JCJiachen Cai
Jiachen Cai
Jian BaiJian Bai
Jian Bai
JCJiaxiao Chen
Jiaxiao Chen
XXXiang Xu
Xiang Xu
QLQianbo Lu
Qianbo Lu
Owing to inevitable errors of the material and fabrication process, the cross-axis sensitivity commonly exists in a large number of MEMS devices based on parallel plate structures. Such cross-axis interference results in the non-negligible rotation of the plate that deteriorates the performance of MEMS devices. Therefore, suppressing the cross-axis sensitivity is extremely critical in the device design. This paper proposes a novel theory to identify the interplay between the cross-axis interference and squeeze film air damping, and further develops a correlated theory of the damping induced suppression. The model of tilting plate with a tiny amplitude is set up by exploiting the Reynolds equation coupled with the equations of the mass deflection, and the analytical expressions of corresponding properties are derived to elucidate the suppression mechanism and its characterization. The analytical calculation and numerical simulation analysis demonstrate that the damping induced improvement effect exists objectively and is remarkable in the condition of a large mass and a small air film thickness. The cross-axis sensitivity rendered by the tilt angle quantitatively declines 80% in terms of the air damping. The theoretical underpinning can be utilized to elaborate the ubiquitous interplay between squeeze film air damping and cross-axis interference in non-vacuum MEMS devices, which is of paramount importance for achieving high performance and stability. More importantly, it is not an exclusive method that can be combined with other methods to minimize the cross-axis interference fully.

29 January 2022 in Sensors
Verified
Journal Article
Open access
PDF file
XXXiang Xu
Xiang Xu
WFWeidong Fang
Weidong Fang
Jian BaiJian Bai
Jian Bai
JCJiaxiao Chen
Jiaxiao Chen
YYYuan Yao
Yuan Yao
QLQianbo Lu
Qianbo Lu
Squeeze film air damping is a significant factor in the design of MEMS devices owing to its great impact on the dynamic performance of vibrating structures. However, the traditional theoretical results of squeeze film air damping are derived from the Reynolds equation, wherein there exists a deviation from the true results, especially in low aspect ratios. While expensive efforts have been undertaken to prove that this deviation is caused by the neglect of pressure change across the film, a quantitative study has remained elusive. This paper focuses on the investigation of the finite size effect of squeeze film air damping and conducts numerical research using a set of simulations. A modified expression is extended to lower aspect ratio conditions from the original model of squeeze film air damping. The new quick-calculating formulas based on the simulation results reproduce the squeeze film air damping with a finite size effect accurately with a maximum error of less than 1% in the model without a border effect and 10.185% in the compact model with a border effect. The high consistency between the new formulas and simulation results shows that the finite size effect was adequately considered, which offers a previously unattainable precise damping design guide for MEMS devices.