Xiang Xu

Mr. Xiang Xu

State Key Laboratory of Modern Optical Instrumentation, Zhejiang University, Hangzhou 310027, China;
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 December 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
JCJiaxiao Chen
Jiaxiao Chen
QLQianbo Lu
Qianbo Lu
Jian BaiJian Bai
Jian Bai
XXXiang Xu
Xiang Xu
YYYuan Yao
Yuan Yao
WFWeidong Fang
Weidong Fang
External temperature changes can detrimentally affect the properties of a microaccelerometer, especially for high-precision accelerometers. Temperature control is the fundamental method to reduce the thermal effect on microaccelerometer chips, although high-performance control has remained elusive using the conventional proportional-integral-derivative (PID) control method. This paper proposes a modified approach based on a genetic algorithm and fuzzy PID, which yields a profound improvement compared with the typical PID method. A sandwiched microaccelerometer chip with a measurement resistor and a heating resistor on the substrate serves as the hardware object, and the transfer function is identified by a self-built measurement system. The initial parameters of the modified PID are obtained through the genetic algorithm, whereas a fuzzy strategy is implemented to enable real-time adjustment. According to the simulation results, the proposed temperature control method has the advantages of a fast response, short settling time, small overshoot, small steady-state error, and strong robustness. It outperforms the normal PID method and previously reported counterparts. This design method as well as the approach can be of practical use and applied to chip-level package structures.

15 December 2022 in Sensors
Verified
Journal Article
Open access
PDF file
XXXiang Xu
Xiang Xu
SWShuang Wu
Shuang Wu
WFWeidong Fang
Weidong Fang
ZYZhe Yu
Zhe Yu
ZJZeyu Jia
Zeyu Jia
QLQianbo Lu
Qianbo Lu
There is a constraint between the dynamic range and the bandwidth of MEMS accelerometers. When the input acceleration is comparatively large, the squeeze film damping will increase dramatically with the increase in the oscillation amplitude, resulting in a decrease in bandwidth. Conventional models still lack a complete vibration response analysis in large amplitude ratios and cannot offer a suitable guide in the optimization of such devices. In this paper, the vibration response analysis of the sensing unit of an accelerometer in large amplitude ratios is first completed. Then, the optimal design of the sensing unit is proposed to solve the contradiction between the dynamic range and the bandwidth of the accelerometer. Finally, the results of the vibration experiment prove that the maximum bandwidth can be achieved with 0~10g external acceleration, which shows the effectiveness of the design guide. The new vibration analysis with the complete model of squeeze film damping is applicable to all sensitive structures based on vibration, not limited to the MEMS accelerometer studied in this thesis. The bandwidth optimal scheme also provides a strong reference for similar structures with large oscillation amplitude ratios.

15 October 2013 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
XXXiang Xu
Xiang Xu
XSXian Chun Song
Xian Chun Song
HJHong Jiang
Hong Jiang
YLYan Feng Li
Yan Feng Li
With the high-speed and high-precision development of CNC machine tool, the vibration problem of ball screws linear guide feed unit has become more and more prominent. The dynamic characteristics was analyzed for ball screws linear guide feed unit, the 3D finite element model was built, the finite element modal analysis was discussed, the natural frequency and vibration modes were obtained, which were compared with the test results. The vibration weaknesses of ball screws linear guide feed unit were found out. The results show that the vibration weaknesses of ball screws linear guide feed unit occur mainly in the ball screws and its connection part with the worktable, its natural frequency are affected by its supporting pattern, and more close to the test results compared with those of ball screw feed unit without considering linear guide, which provide theoretical basis for the structure optimization of ball screws linear guide feed unit.

8 February 2022 in IEEE Sensors Journal
Verified
Journal Article
Closed access
WFWeidong Fang
Weidong Fang
JCJiachen Cai
Jiachen Cai
Jian BaiJian Bai
Jian Bai
JCJiaxiao Chen
Jiaxiao Chen
XXXiang Xu
Xiang Xu
QLQianbo Lu
Qianbo Lu
Owing to inevitable errors of the material and fabrication process, the cross-axis sensitivity commonly exists in a large number of MEMS devices based on parallel plate structures. Such cross-axis interference results in the non-negligible rotation of the plate that deteriorates the performance of MEMS devices. Therefore, suppressing the cross-axis sensitivity is extremely critical in the device design. This paper proposes a novel theory to identify the interplay between the cross-axis interference and squeeze film air damping, and further develops a correlated theory of the damping induced suppression. The model of tilting plate with a tiny amplitude is set up by exploiting the Reynolds equation coupled with the equations of the mass deflection, and the analytical expressions of corresponding properties are derived to elucidate the suppression mechanism and its characterization. The analytical calculation and numerical simulation analysis demonstrate that the damping induced improvement effect exists objectively and is remarkable in the condition of a large mass and a small air film thickness. The cross-axis sensitivity rendered by the tilt angle quantitatively declines 80% in terms of the air damping. The theoretical underpinning can be utilized to elaborate the ubiquitous interplay between squeeze film air damping and cross-axis interference in non-vacuum MEMS devices, which is of paramount importance for achieving high performance and stability. More importantly, it is not an exclusive method that can be combined with other methods to minimize the cross-axis interference fully.

29 January 2022 in Sensors
Verified
Journal Article
Open access
PDF file
XXXiang Xu
Xiang Xu
WFWeidong Fang
Weidong Fang
Jian BaiJian Bai
Jian Bai
JCJiaxiao Chen
Jiaxiao Chen
YYYuan Yao
Yuan Yao
QLQianbo Lu
Qianbo Lu
Squeeze film air damping is a significant factor in the design of MEMS devices owing to its great impact on the dynamic performance of vibrating structures. However, the traditional theoretical results of squeeze film air damping are derived from the Reynolds equation, wherein there exists a deviation from the true results, especially in low aspect ratios. While expensive efforts have been undertaken to prove that this deviation is caused by the neglect of pressure change across the film, a quantitative study has remained elusive. This paper focuses on the investigation of the finite size effect of squeeze film air damping and conducts numerical research using a set of simulations. A modified expression is extended to lower aspect ratio conditions from the original model of squeeze film air damping. The new quick-calculating formulas based on the simulation results reproduce the squeeze film air damping with a finite size effect accurately with a maximum error of less than 1% in the model without a border effect and 10.185% in the compact model with a border effect. The high consistency between the new formulas and simulation results shows that the finite size effect was adequately considered, which offers a previously unattainable precise damping design guide for MEMS devices.