The intrinsic characteristic of piezoelectric actuators (PEA), known as hysteresis, has been demonstrated to diminish the capability and stability of the system significantly. This paper proposes a modified-generalized Prandtl–Ishlinskii (MGPI) model to describe the rate-dependent hysteresis in piezoelectric actuators. The developed model incorporates a voltage change rate function to replace the first part of the generalized Prandtl–Ishlinskii (GPI) model. Additionally, the model integrates the cubic polynomial into the envelope function, along with the dynamic thresholds and weights. When describing the hysteresis of the piezoelectric actuator (PEA), the model parameters are identified using the Improved Grey Wolf Optimizer (IGWO) algorithm. To prevent the algorithm from getting trapped in local optima, the cubic chaotic mapping is utilized for population initialization, as well as a nonlinear convergence factor, and the Levy flight strategy factor is introduced to update the Wolf pack’s position. The rate-dependent hysteresis behavior of a PEA under excitation in the 1–200 Hz frequency range was experimentally measured. The measured data were used to demonstrate the validity of the proposed MGPI model. The relative root-mean-square error and the relative maximum error of the MGPI model are 1.41% and 6.00%, respectively, which are lower than those of the GPI model, which are 3.15% and 10.58%. Under the composite frequency driving, the outputs of the GPI model and MGPI model were compared with the measured data of the PEA, the results suggest that the MGPI model and the IGWO algorithm can more accurately describe the rate-dependent hysteresis of the piezoelectric actuators.
Inchworm piezoelectric actuators have attracted much attention in the field of precision positioning due to the advantages of a large stroke, high output force, and high resolution. However, traditional inchworm piezoelectric actuators use two sets of clamps and a set of drive structures to achieve stepping motion, which generally requires at least three piezoelectric stacks, resulting in a complex structure and the control system. Several methodologies have been advanced to minimize the utilization of piezoelectric stacks. However, there still exists the issue of excessive volume. Therefore, an inchworm piezoelectric actuator with a single-clamp and single drive structure is proposed in the study, which provides a compact size and smaller volume. The clamping mechanism comprises two sets of clamping feet with opposite displacement, which alternate contact with the guide frame and adjustable plate to ensure that the clamping mechanism always has frictional force and accomplishes the stepping motion. The testing of the actuator’s step distance, output force, and other parameters was conducted utilizing a displacement sensor. Experimental results indicate that the actuator achieved a maximum speed of 174.3 μm/s and an output force of 8.6 N when the frequency and voltage were 19 Hz and 150 V.
A high-speed atomic force microscope (HS-AFM) based on a tip-sample combined scanning architecture is presented. In this system, the X-scanner, which is separated from the AFM head, carries the sample and scans along the fast-axis. The Y and Z scanners integrated in the AFM head oscillate an ultrashort cantilever probe and scan in the other two dimensions. The optical beam deflection method is improved to enable the laser to track the probe over a wide scan range. A novel probe holder realizes easy exchange and alignment of the probe. Due to the separation of the X and Y scanners, both appear with better dynamic performance and carrying capacity. Experiments show that the HS-AFM established in this work can achieve a line rate of up to 100 Hz with the basic proportional-integral-derivative control algorithm and linear driving. The permissible sample size and mass can be as large as several centimeters and above 40 g.
In this work, a novel bipedal stepping piezoelectric actuator based on stick–slip principle is proposed. An integrated stator with symmetrically positioned dual driving feet has been developed, characterized by its element analysis. Key structural parameters were optimized, and a prototype was fabricated for a series of experiments. The experimental results demonstrate that the actuator attains a maximum output speed of 4550 μm/s at a voltage of 150 V and a frequency of 350 Hz. The stepping efficiency is measured at 0.886, with a maximum horizontal load capacity of 170 g. Furthermore, the actuator exhibits a displacement resolution of 180 nm, making it highly suitable for precision actuation and applications in fields such as biomedical engineering.
A combined tip-sample scanning architecture can improve the imaging speed of atomic force microscopy (AFM). However, the nonorthogonality between the three scanners and the nonideal response of each scanner cause measurement errors. In this article, the authors systematically analyze the influence of the installation and response errors of the combined scanning architecture. The experimental results show that when the probe in the homemade high-speed AFM moves with the Z-scanner, the spot position on the four-quadrant detector changes, thus introducing measurement error. Comparing the experimental results with the numerical and theoretical results shows that the undesired motion of the Z-scanner introduces a large error. The authors believe that this significant error occurs because the piezoelectric actuator not only stretches along the polarization direction but also swings under nonuniform multifield coupling. This article proposes a direction for further optimizing the instrument and provides design ideas for similar high-speed atomic force microscopes.
An accurate 3D pose estimation of spherical objects remains challenging in industrial inspections and robotics due to their geometric symmetries and limited feature discriminability. This study proposes a texture-optimized simulation framework to enhance pose prediction accuracy through optimizing the surface texture features of the design samples. A hierarchical texture design strategy was developed, incorporating complexity gradients (low to high) and color contrast principles, and implemented via VTK-based 3D modeling with automated Euler angle annotations. The framework generated 2297 synthetic images across six texture variants, which were used to train a MobileNet model. The validation tests demonstrated that the high-complexity color textures achieved superior performance, reducing the mean absolute pose error by 64.8% compared to the low-complexity designs. While color improved the validation accuracy universally, the test set analyses revealed its dual role: complex textures leveraged chromatic contrast for robustness, whereas simple textures suffered color-induced noise (a 35.5% error increase). These findings establish texture complexity and color complementarity as critical design criteria for synthetic datasets, offering a scalable solution for vision-based pose estimation. Physical experiments confirmed the practical feasibility, yielding 2.7–3.3° mean errors. This work bridges the simulation-to-reality gaps in symmetric object localization, with implications for robotic manipulation and industrial metrology, while highlighting the need for material-aware texture adaptations in future research.