Ana Isabel Fernández Calvo

Dr. Ana Isabel Fernández Calvo

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 July 2021 in Metals
Verified
Journal Article
Open access
PDF file
AAAsier Bakedano Abaunza
Asier Bakedano Abaunza
ANAndrea Niklas
Andrea Niklas
ACAna Isabel Fernández Calvo
Ana Isabel Fernández Calvo
Gorka PlataGorka Plata
Gorka Plata
JLJokin Lozares
Jokin Lozares
Carlos BerlangaCarlos Berlanga
Carlos Berlanga
The use of secondary aluminium is increasingly being promoted in the automotive industry for environmental reasons. The purpose of this study was to demonstrate that it is possible to obtain a recycled AlSi10MnMg(Fe) aluminium alloy with equal metallurgical quality to that of a primary AlSi10MnMg alloy when an adequate melt treatment is applied. The melt treatment consisted of deoxidation, degassing and skimming in accordance with the detailed procedure described in this article. The metallurgical qualities of one primary and two secondary alloys were assessed using thermal analysis, the density index test, the macroinclusion test and the microinclusion level test before and after melt treatment. The thermal analysis allowed us to compare the variables of the solidification cooling curve (Al primary temperature and its undercooling; Al-Si eutectic temperature and its predictive modification rate). The density index test was used to evaluate the hydrogen gas content in the melt. The macroinclusion test was used to evaluate the melt cleanliness, while the microinclusion level test was used to perform the inclusion identification and quantification analyses. This study showed the feasibility of manufacturing structural components using 100% recycled secondary aluminium alloy through V-HPDC technology.

6 September 2018 in Metals
Verified
Journal Article
Open access
PDF file
GAGarikoitz Artola
Garikoitz Artola
AAAlberto Arredondo
Alberto Arredondo
ACAna Isabel Fernández Calvo
Ana Isabel Fernández Calvo
Javier AldazabalJavier Aldazabal
Javier Aldazabal
Hydrogen embrittlement susceptibility ratios calculated from slow strain rate tensile tests have been employed to study the response of three high-strength mooring steels in cold and warm synthetic seawater. The selected nominal testing temperatures have been 3 °C and 23 °C in order to resemble sea sites of offshore platform installation interest, such as the North Sea and the Gulf of Mexico, respectively. Three scenarios have been studied for each temperature: free corrosion, cathodic protection and overprotection. An improvement on the hydrogen embrittlement tendency of the steels has been observed when working in cold conditions. This provides a new insight on the relevance of the seawater temperature as a characteristic to be taken into account for mooring line design in terms of hydrogen embrittlement assessment.

1 January 2022 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
EBE. Barbarias
E. Barbarias
ANA. Niklas
A. Niklas
ILI. Lizarralde
I. Lizarralde
MGM. Garat
M. Garat
ABA. Bakedano
A. Bakedano
ACAna Isabel Fernández Calvo
Ana Isabel Fernández Calvo

Verified
Journal Article
Open access
PDF file
Javier VivasJavier Vivas
Javier Vivas
ACAna Isabel Fernández Calvo
Ana Isabel Fernández Calvo
EAEgoitz Aldanondo
Egoitz Aldanondo
UIUxue Irastorza
Uxue Irastorza
PAPedro Alvarez
Pedro Alvarez
In this work, the friction stir weldability of two structural high-pressure die casting aluminum alloys designed to manufacture thin-walled automotive components is investigated and compared. AlSi10MnMg and AlMg4Fe2 alloys were friction stir welded at a high welding speed (from 500 to 2000 mm/min) for a fixed rotation speed of 1500 RPM. The investigation was performed by studying the material flow influence on defect formation and microstructure, the mechanical properties of the welds and the forces that act during the friction stir welding process. The AlSi10MnMg alloy shows a lower incidence of defects than the AlMg4Fe2 alloy at all welding speeds investigated. Both materials present a great friction stir welding performance at 500 mm/min with a high joint efficiency in terms of ultimate tensile strength: 92% in AlSi10MnMg alloy and 99% in AlMg4Fe2 alloy.

11 May 2023 in Crystals
Verified
Journal Article
Open access
PDF file
ACAna Isabel Fernández Calvo
Ana Isabel Fernández Calvo
CDClara Delgado
Clara Delgado
PDPhilippe Dufour
Philippe Dufour
EAEgoitz Aldanondo
Egoitz Aldanondo
MDMario Díaz
Mario Díaz
MGM.Belén García
M.Belén García
The end of fife (EoL) of new aircraft panels made of Al-Li alloys in which the stringers and skin were joined, either by laser beam welding (LBW) or by friction stir welding (FSW), was investigated at the lab scale. Different cutting strategies, ranging from cutting only for size reduction to full separation of all materials, including the removal of the welded seam, were defined, with the objective of recycling the maximum amount of panel scrap back into high-quality aircraft Al-Li alloys. Those welded aerostructures were coated with two novel Cr-free coating systems. The effect of the coatings on the recyclability of the panels and the need to eliminate the primer and topcoats were researched. Fading/enrichment of the alloying elements during recycling was determined. The chemical compatibility of the recycled alloys with four commercial Al-Li alloys was examined. The EoL route that maximized closed-loop recycling and the conservation of the valuable alloying elements was identified. Nine out of the ten configurations were found to be compatible with joint recycling. Only the LBW structure with ER4047 filler wire required sorting into scrap fractions and removing the weld seam. Decoating by corundum blasting followed by cutting before remelting is the recommended EoL process.

23 July 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
IMIbon Miguel
Ibon Miguel
GAGarikoitz Artola
Garikoitz Artola
Jon Iñaki ArrizubietaJon Iñaki Arrizubieta
Jon Iñaki Arrizubieta
ACAna Isabel Fernández Calvo
Ana Isabel Fernández Calvo
CACarlos Angulo
Carlos Angulo
The combination of wrought materials and laser-based directed energy deposition (DED-LB) is being increasingly used for manufacturing new and repairing old or damaged components in several industries. Aerospace components made of Inconel 718 featuring small-thickness DED-LB buildups are a remarkable example of such a combination due to the high added value it brings. Despite that these are usually critical components, the miniature testing methods to assess the local mechanical properties in the buildup area are not fully developed. This work contributes to this miniature testing development with an improvement of the small punch testing (SPT) technique for measuring the mechanical properties of the weld line between the DED-LB and the wrought substrate. A new criterion for weld line positioning in the SPT specimens is proposed and applied on samples of hybrid wrought/DED-LB Inconel 718. The results of positioning the weld line at the necking site of the SPT specimen show that the proposed approach is valid for assessing the properties of the transition zone between the wrought and additive states. For the specific conditions tested and taking the wrought material as a reference, the strength of the Inconel 718 drops 10% in the weld line and 20% in the buildup.