High-pressure die casting dies are produced in most cases by conventional subtractive manufacturing processes. In this case, a massive design of the die usually ensures high stability during the casting process. However, at the same time, it leads to low flexibility in casting production and high material costs. The basic approach in the present work is to reduce the conventional subtractive production process of a die casting die in favor of a flexible, modular design, where only a few contour elements of the die have to be replaced for achieving different castings. In order to pave the way for this design principle, basic thermal and structural properties of a lightweight design die casting die were analyzed. The finite element calculations carried out showed that the modular lightweight die casting die consumes considerably less energy for preheating and during operation. Due to the reduced stiffness and material, however, calculated deformations and stresses in the die are considerably higher during the casting process. Although the initial calculation results look very promising, further knowledge must be gained in order to ensure the future success of modular lightweight die casting dies.
The initial investigation evaluates the feasibility of ultra high performance concrete (UHPC) as a material for reusable molds in aluminum casting. Two specific UHPC formulations were investigated: one based on ordinary Portland cement (OPC) and another utilizing alkali-activated materials (AAM). The study focused on investigating the surface through roughness measurements and the thermal durability through repeated casting cycles. The thermal stability of the molds was investigated by thermogravimetric analysis, mercury intrusion porosimetry, crack segmentation, optical microscopy, and electron microscopy. Results indicate that molds fabricated from AAM-UHPC exhibit relatively better performance in terms of maintaining structural integrity and surface quality over repeated uses. AAM-UHPC molds were able to withstand up to ten casting cycles with acceptable surface degradation and no significant failure, while OPC-UHPC molds exhibited a faster degradation under similar conditions. Microstructural changes and the interaction of UHPC materials with molten aluminum were investigated, highlighting the low adhesion and defect formation. Additionally, the molds demonstrated sound casting quality, with a grain size comparable to that achieved using traditional steel molds (~ 90 µm), underscoring the potential of UHPC materials for enhancing casting quality and efficiency. The study concludes that UHPC, particularly with alkali-activated formulations, shows promise for low-pressure casting environments.
Increasing the service life of die casting dies is an important goal of the foundry industry. Approaches are either material- or process-related. Despite new material concepts, hot work steels such as H11 are still predominantly used in the uncoated condition for die casting dies. In order to withstand the stresses that occur, this steel is used exclusively in the quenched and tempered condition. Required properties such as high high-temperature strength and high hardness combined with high toughness are, in principle, contradictory and can only be adjusted consistently over the entire die by furnace-based heat treatment. However, the results of various investigations have shown that improvements in the thermal shock resistance and wear resistance of hot work tool steels can be achieved by thermally influencing the microstructure near the surface. Based on these studies and related findings, an approach to surface heat treatment using the electron beam was developed. Due to the particle character of the radiation and the associated possibility of high-frequency beam deflection, the electron beam offers significantly greater flexibility in energy input into the workpiece surface compared with lasers or induction. The overall technological concept envisages replacing furnace-based heat treatment in the production of casting dies by localized and demand-oriented boundary layer heat treatment with the electron beam. The experiments include, on the one hand, the experimental determination of a suitable temperature–time interval with a focus on short-term austenitization. On the other hand, a simulation-based approach of boundary layer heat treatment with validation of a suitable heat source is investigated. Regarding short-term austenitization, the corresponding temperature and time range could be narrowed down more precisely. Some of these parameter combinations seem to be very suitable for practical use. The test specimens show a hard surface layer with a depth of at least up to 6 mm and a very tough buffer layer. Numerical simulation is used to estimate the resulting metallurgical microstructure and the achievable hardness as a function of the temperature–time interval. In addition, the results provided show the possibility of determining and optimizing the material properties by means of a simulation-based approach within the framework of a purely digital process planning and subsequently transferring them into a process planning. In the technical implementation, a temperature control was first established by means of a two-color pyrometer. In the further course of research, the pyrometer will be supplemented by an internally installed infrared camera, which will allow the reproducible setting of specified temperature profiles even for complex, large-area contours in the future.
Conventional cooling channels used in die casting molds exhibit significant drawbacks, resulting in extended cooling times for cast parts. Issues such as the formation of dirt, limescale, and corrosion substantially diminish the thermal efficiency of these channels, leading to challenges in achieving uniform cooling and potential quality issues. In response to these challenges, this study proposes Topology Optimization as a novel approach. It involves designing cooling structures through Topology Optimization to replace traditional cooling channels, incorporating both Discrete and Gaussian boundary conditions to optimize thermal efficiency. Additionally, Structural Topology Optimization is employed to ensure structural integrity, preventing deformation or yielding under high loads during the die casting process. Numerical analysis revealed superior thermal performance compared to conventional channels, particularly when subjected to Discrete and Gaussian boundary conditions. Furthermore, the application of the latter establishes conformal cooling and minimizes temperature gradients in the casting, reducing casting defects such as shrinkage porosity. These findings highlight the efficacy of Topology Optimization in addressing the challenges of traditional cooling methods, with wide-ranging implications for manufacturing processes utilizing permanent molds for shaping materials.
In the case of casting processes with permanent molds, there is still a relatively pronounced lack of knowledge regarding the locally prevailing heat transfer between casts and mold. This in turn results in an insufficient knowledge of the microstructure and the associated material properties in the areas of the casting component close to the surface. Therefore, this work deals with the design and evaluation of a test tool with an integrated sensor system for temperature measurements, which was applied to obtain a time-dependent heat transfer coefficient (HTC) during casting solidification. For this purpose, the setup, design and computational approach are described first. Special attention is paid to the qualification of the multi-depth sensor and the calculation method. For the calculations, an inverse estimation method (nonlinear sequential function) was used to obtain the HTC profiles from the collected data. The developed sensor technology was used in a test mold to verify the usability of the sensor technology and the plausibility of the obtained calculation results under real casting conditions and associated temperature loads. Both the experimental temperature profiles and the HTC profiles showed that, in the evaluated casting series, the peak values determined were close to each other and reached values between 6000 W/(m2·K) and 8000 W/(m2·K) during solidification.