Concretes with dispersed reinforcement are increasingly used in structural engineering. The basic source of knowledge on their application and design are the Model-Code 2010 guidelines. These guidelines, however, apply mainly to steel rebar reinforcement and are not fully sufficient in the analysis of the load-bearing capacity of elements made of concrete with dispersed reinforcement. Therefore, scientific research in this field is carried out continuously. The main goal of our work is to provide experimental data for the calibration of constitutive models of the cracking mechanics of concrete with reinforcement in the form of steel and polypropylene fibers. This article shows the possibility of using the digital image correlation system (DIC) to achieve this goal. The method of sample preparation and the method of conducting the tests were modeled on the recommendations contained in the PN-EN 14651: 2007 standard. The tests were carried out on prismatic elements with a notch loaded in a three-point bending setup. The results of standard strength tests are presented in the form of column graphs and tables. As an extension, the results of calculations of energy dissipated in fracture process are given. Moreover, the experimentally obtained graphs of the relationship between the force, displacement and crack opening were presented, which were supplemented with the images of crack development obtained with the use of DIC. The development of the crack net is characterized not only qualitatively but also quantitatively as a function of deflection or crack mouth opening displacement. Conclusions concerning the adopted research methodology and the tested materials are presented at the end of the article.
In the presented paper the local instabilities occurring in compression test of perforated thin-walled bars of low slenderness are observed using digital image correlation system ARAMIS. The tested samples slenderness is so low, that from theoretical point of view we are dealing with compression tests of some perforated shells. The samples are made from typical low carbon steel, which has to be treated as elasto-plastic material. Because of that, the final geometry of the sample (after unloading) is also analysed giving a good data for calibration of the theory of elasto-plasticity for large deformations. In analysed cases the total strain values are not exceptionally large, while local rotation (and permanent deformations) have significant values.
The development of measurement methods, and in particular digital image correlation (DIC) systems, which are designed to measure of entire displacements and deformations fields, opens up new areas of research. In general, the materials constitutive relations are formulated in such a way that material parameters could be determined with relatively simple experimental tests carried out on samples with uniform (approximately) stress and strain fields. Then it is possible to apply them to complex boundary value problems formulated e.g. in the small or large deformation theories. The application of DIC allows to verify the accuracy of their predictions by comparing the results of the experiment with solutions to boundary value problems obtained using the finite element method (FEM).
Experimental research on mechanical properties of hardened polyethylene HDPE, is developed in the paper. The conditions of hydraulic impact simulation, caused by sudden opening or closing of the valve or by working pomp were adopted in the model. The created in such conditions shock wave moves at a high speed causing additional dangerous dynamic loadings, which lead to faster pipe wear process. The aim of this study is to determine Young's modulus of the pipe material in the cyclic load conditions. The assumed amplitude and frequency of the applied load relates to variation of the impact wave pressure also the speed of the disturbances propagation are taken from experimental measurement of the real water hammer. The measured Young's modulus is higher than that obtained from a static tensile test. The presented study arises from the need to verify the actual value of pipe material mechanical properties, i.e. longitudinal stiffness, for designing of hydraulic pipes under conditions of water hammer.
1 November 2019 in IOP Conference Series: Materials Science and Engineering
This article presents the results of a systematic comparison of predictions of the thin-walled beam theory and shell theory in the context of bending of elastic thin-walled beams with an open or closed cross-section. The results for shell theory were obtained using FEM and the ABAQUS/Standard program. The bending task of the thin-walled beam was decomposed into the task with a symmetrical and anti-symmetrical loading, so that the bending and torsion of the thin-walled element would be better visible. In order to objectify the comparison, two coefficients characterizing the mutual similarity of functions were introduced: root mean square deviation coefficient determined for the selected cross-section (in relation to the entire contour) and a coefficient determining the maximum relative difference of a given quantity. The comparison was made for both the stress and the displacement state.