Concretes with dispersed reinforcement are increasingly used in structural engineering. The basic source of knowledge on their application and design are the Model-Code 2010 guidelines. These guidelines, however, apply mainly to steel rebar reinforcement and are not fully sufficient in the analysis of the load-bearing capacity of elements made of concrete with dispersed reinforcement. Therefore, scientific research in this field is carried out continuously. The main goal of our work is to provide experimental data for the calibration of constitutive models of the cracking mechanics of concrete with reinforcement in the form of steel and polypropylene fibers. This article shows the possibility of using the digital image correlation system (DIC) to achieve this goal. The method of sample preparation and the method of conducting the tests were modeled on the recommendations contained in the PN-EN 14651: 2007 standard. The tests were carried out on prismatic elements with a notch loaded in a three-point bending setup. The results of standard strength tests are presented in the form of column graphs and tables. As an extension, the results of calculations of energy dissipated in fracture process are given. Moreover, the experimentally obtained graphs of the relationship between the force, displacement and crack opening were presented, which were supplemented with the images of crack development obtained with the use of DIC. The development of the crack net is characterized not only qualitatively but also quantitatively as a function of deflection or crack mouth opening displacement. Conclusions concerning the adopted research methodology and the tested materials are presented at the end of the article.
The paper describes the essential functional and operational features of the Under Sleeper Pads (USPs), used in ballasted rail track systems. The overview of appropriate test methods for determining the values of relevant parameters for the purposes of using vibro-acoustic isolators was presented, with special attention drown to the changes resulting from the introduction of the PN-EN 16730 standard in this field. Due to the given testing procedures for USPs, selected examples of the normative testing methods of the USPs’ carried out at the Faculty of Civil Engineering of the Warsaw University of Technology with the results were presented.
In the presented paper the local instabilities occurring in compression test of perforated thin-walled bars of low slenderness are observed using digital image correlation system ARAMIS. The tested samples slenderness is so low, that from theoretical point of view we are dealing with compression tests of some perforated shells. The samples are made from typical low carbon steel, which has to be treated as elasto-plastic material. Because of that, the final geometry of the sample (after unloading) is also analysed giving a good data for calibration of the theory of elasto-plasticity for large deformations. In analysed cases the total strain values are not exceptionally large, while local rotation (and permanent deformations) have significant values.
This paper presents an experimental study on the elastic support in a discrete rail fastening system used in a ballastless tram track structure. The study focuses on the elastic support of the anchor element, specifically the Pm49 baseplate. These elements significantly influence environmental pollution along tram routes, such as vibration (at low frequencies) or noise (at high frequencies), as well as static and dynamic rail deflections. The authors outline a methodology for identifying the static and dynamic characteristics of the discrete elastic support in laboratory conditions. The procedure follows the European standard EN 13146-9 for track category A (tramway), as classified according to the European standard EN 13481-5. The study analyzes how the thickness and density of the tested materials affect stiffness. Additionally, it examines the correlation between parameters identified easily on-site (thickness, Shore hardness and density) and laboratory-determined parameters (static and dynamic stiffness), which are costly and time-consuming to measure. The research confirms that prototype prefabricated vibration isolation baseplate pads made of styrene butadiene rubber (SBR) granules, recycled from end-of-life car tires, can achieve equivalent basic static and dynamic parameters, compared to underlays made of two-component polyurethane (PU) resin. This aligns with the strategy of promoting sustainable materials in construction. The innovative and prefabricated SBR rubber baseplate pads can also be used in repair and maintenance works (regardless of weather conditions), as they enable the quick launch of tram traffic. The results of the research included in this article can be used by other scientists, recycled rubber producers, tram track designers or construction site engineers.
The determination of compressive strength of hemp–lime composite (HLC) is currently based on diverse and non-unified approaches, which complicates the direct comparison of results obtained in different studies. This study compares commonly used strength-determination methods using a dedicated experimental dataset and proposes a new, more universal approach, defining compressive strength as the stress corresponding to 1% permanent strain. Cubic specimens (150 × 150 × 150 mm) were produced at three compaction levels (150%, 170%, 190%) and tested under uniaxial compression. Increasing compaction increased density and resulted in compressive strengths of 219, 316, and 349 kPa, respectively. Methods based on fixed strain levels (5% and 10%) showed good repeatability but primarily reflected serviceability limits, whereas those based on loss of linearity or stiffness reduction were less reliable and highly sensitive to curve interpretation. The proposed 1% permanent-strain method accurately captured the onset of irreversible deformation and aligned with the real behavior of hemp–lime infill in frame structures, supporting its use for standardizing compressive-strength testing of hemp–lime composites.