Continuous Fiber Reinforced Thermoplastic (CFRT) hybrid parts offer interesting possibilities for lightweight application, which can exceed the capabilities of mono material metal or CFRT parts. In this case, the joining technology oftentimes is the limiting factor. This study investigates a joining operation with metal pin structures which are additively manufactured via powder bed fusion featuring different diameters and tip geometries, which are inserted into the locally infrared heated CFRT part. The resulting fiber rearrangement is assessed using transmitted light microscopy, confocal laser scanning microscopy as well as micro-computer-tomography. It could be shown that for all assessed pin variants a similar distinct fiber displacement can be seen and that the pin diameter has a significant effect on the resulting fiber orientation with smaller pin diameters being advantageous because of gentle fiber displacement and reduced undulation. The tip geometry has only minor effect on the fiber orientation. Especially in the X/Y plane no systematic influence of the tip geometry on the fiber displacement could be observed. Based on the gained insights a three-stage model of the fiber orientation processes is proposed.
In this study, quasi-unidirectional continuous fiber reinforced thermoplastics (CFRTs) are joined with metal sheets via cold formed cylindrical, elliptical and polygonal pin structures which are directly pressed into the CFRT component after local infrared heating. In comparison to already available studies, the unique novelty is the use of non-rotational symmetric pin structures for the CFRT/metal hybrid joining. Thus, a variation in the fiber orientation in the CFRT component as well as a variation in the non-rotational symmetric pins’ orientation in relation to the sample orientation is conducted. The created samples are consequently mechanically tested via single lap shear experiments in a quasi-static state. Finally, the failure behavior of the single lap shear samples is investigated with the help of microscopic images and detailed photographs. In the single lap shear tests, it could be shown that non-rotational symmetric pin structures lead to an increase in maximum testing forces of up to 74% when compared to cylindrical pins. However, when normalized to the pin foot print related joint strength, only one polygonal pin variation showed increased joint strength in comparison to cylindrical pin structures. The investigation of the failure behavior showed two distinct failure modes. The first failure mode was failure of the CFRT component due to an exceedance of the maximum bearing strength of the pin-hole leading to significant damage in the CFRT component. The second failure mode was pin-deflection due to the applied testing load and a subsequent pin extraction from the CFRT component resulting in significantly less visible damage in the CFRT component. Generally, CFRT failure is more likely with a fiber orientation of 0° in relation to the load direction while pin extraction typically occurs with a fiber orientation of 90°. It is assumed that for future investigations, pin structures with an undercutting shape that creates an interlocking joint could counteract the tendency for pin-extraction and consequently lead to increased maximum joint strengths.
28 November 2024 in Journal of Advanced Joining Processes
Hybrid components consisting of continuous fiber reinforced thermoplastic (CFRT) and steel components exhibit promising potential in advanced lightweight construction. However, the joining operation presents a significant challenge due to the materials’ distinct physical and chemical properties. This paper studies a joining method in which dual pin arrays protruding from the surface of the metal component are inserted into the locally heated CFRT component to create a form-fitting joint. The primary objective is to scrutinize the influence of various CFRT materials on joint formation and quantify the resulting properties. The fiber type (glass and carbon) and fiber architecture (unidirectional and bidirectional reinforcement) are varied. All materials could successfully be joined via the direct pin pressing process, while depending on the CFRT material, distinct characteristic fiber morphologies could be identified. Bidirectionally reinforced carbon fiber reinforced samples showed the highest overall strength, while unidirectionally glass fiber reinforced samples showed the highest energy absorption and second highest ultimate strength.
As a new and innovative processing method for fabrication for fiber-reinforced thermoplastic composites (CFRTs), the feasibility of ultrasonic welding technology was proven in several studies. This method offers potential for the direct manufacturing of CFRT–metal structures via embedded pin structures. Despite the previous studies, a deeper understanding of the process of energy input and whether fibers work as energy directors and consequently can, in combination with chosen processing parameters, influence the consolidation quality of the CFRTs, is still unknown. Consequently, the aim of this work is to establish a deeper process understanding of the ultrasonic direct impregnation of fiber-reinforced thermoplastics with an emphasis on the fiber’s function as energy directors. Based on the generated insights, a better assessment of the feasibility of direct, hybrid part manufacturing is possible. The produced samples were primarily evaluated by optical and mechanical test methods. It is demonstrated that with higher welding time and amplitude, a better consolidation quality can be achieved and that independent of the process parameters chosen in this study, no significant fiber breakage occurs. This is interpreted as a sign of a gentle impregnation process. Furthermore, based on the examination of single roving and 5-layer set-ups, it is shown that the glass fibers function as energy directors and can influence the transformation of sonic energy into thermal energy. In comparison to industrially available CFRT material, the mechanical properties are weaker, but materials and processes offer potential for significant improvement. Based on these findings, proposals for a direct impregnation and joining process are made.
1 January 2023 in Science and Engineering of Composite Materials
Continuous fiber-reinforced thermoplastics (CFRTs) can in combination with high-strength metals offer characteristics that cannot be achieved with mono-material parts. One possible example is the combination of locally high-temperature resistance in the metal component with superior weight-related mechanical properties due to the CFRT component. This approach requires a reliable and durable joining technology, which considers the material-specific properties and allows to exploit the full potential of CFRT/metal hybrid parts. A promising approach in the field of CFRT/metal joining is the use of metallic pins, which can be embedded in the locally heated CFRT component to create a form-fitting joint. In the current state of the art, primarily single-pins are investigated and characterized: especially the distinct fiber orientation in the direct pin pressing process is only described for single-pin joints. Behind this background, the present study aims at creating an understanding of the fiber orientation mechanism for multi-pin arrays. Therefore, in the scope of this study, unidirectional reinforced glass fiber/polypropylene samples are joined via direct pin pressing and infrared heating with different 1D and 2D multi-pins arrays with different pin-diameters, spacing and pin distributions. The resulting joint morphology is consequently analyzed using micro-computer-tomography. Based on the performed investigations, a model for the fiber displacement mechanism is proposed, and the first recommendations for the design of fiber-friendly multi-pin joints with unidirectional reinforcements are given. It showed that especially pin-spacing in fiber orientation in dependency of the pin diameter is critical for a fully reconsolidated joint quality, and it is suggested that a pin-offset in the fiber direction is beneficial for a fiber-friendly joining process.