Andrzej Ambroziak

Prof. Andrzej Ambroziak

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 February 2020 in Coatings
Verified
Journal Article
Open access
PDF file
MMMonika Michalak
Monika Michalak
Leszek ŁatkaLeszek Łatka
Leszek Łatka
Pawel SokolowskiPawel Sokolowski
Pawel Sokolowski
ANAneta Niemiec
Aneta Niemiec
AAAndrzej Ambroziak
Andrzej Ambroziak
The Al2O3 + TiO2 coatings are of the interest of surface technology and tribology due to their good wear resistance and enhanced toughness comparing to pure Al2O3 coatings. However, the detailed effect of the used feedstock powder, is often neglected. Here, this work focuses on the deposition of Al2O3 + 13 wt % TiO2 coatings by atmospheric plasma spraying (APS) method as well as on their microstructure, phase composition and selected mechanical properties, in the reference to the route of the powder feedstock preparation. The commercial powder Metco 6221 in agglomerated and sintered form was used as a feedstock material during spraying, due to the fact that, so far, sintered or cladded powders are the most studied ones. The 2k + 1 spray experiment allowed to evaluate the influence of two variables, namely spray distance and torch linear velocity, on the coating microstructure. Afterwards, the coating adhesion was measured by the means of pull-off test. The correlations between Vickers microhardness, fracture toughness (Kc) as well as the coating morphology and phase composition were investigated. Finally, the dry sliding wear resistance was studied by using Ball-on-Disc method.

9 June 2020 in Materials
Verified
Journal Article
Open access
PDF file
MMMonika Michalak
Monika Michalak
FTFilofteia-Laura Toma
Filofteia-Laura Toma
Leszek ŁatkaLeszek Łatka
Leszek Łatka
Pawel SokolowskiPawel Sokolowski
Pawel Sokolowski
MBMaria Barbosa
Maria Barbosa
AAAndrzej Ambroziak
Andrzej Ambroziak
In this work, the alumina (Al2O3) and alumina-titania coatings with different contents of TiO2, i.e., Al2O3 + 13 wt.% TiO2 and Al2O3 + 40 wt.% TiO2, were studied. The coatings were produced by means of powder and liquid feedstock thermal spray processes, namely atmospheric plasma spraying (APS), suspension plasma spraying (SPS) and suspension high-velocity oxygen fuel spraying (S-HVOF). The aim of the study was to investigate the influence of spray feedstocks characteristics and spray processes on the coating morphology, microstructure and phase composition. The results revealed that the microstructural features were clearly related both to the spray processes and chemical composition of feedstocks. In terms of phase composition, in Al2O3 (AT0) and Al2O3 + 13 wt.% TiO2 (AT13) coatings, the decrease in α-Al2O3, which partially transformed into γ-Al2O3, was the dominant change. The increased content of TiO2 to 40 wt.% (AT40) involved also an increase in phases related to the binary system Al2O3-TiO2 (Al2TiO5 and Al2−xTi1+xO5). The obtained results confirmed that desired α-Al2O3 or α-Al2O3, together with rutile-TiO2 phases, may be preserved more easily in alumina-titania coatings sprayed by liquid feedstocks.

22 July 2016 in Surface Engineering
Verified
Journal Article
Closed access
Marcin WinnickiMarcin Winnicki
Marcin Winnicki
Agnieszka BaszczukAgnieszka Baszczuk
Agnieszka Baszczuk
Małgorzata RutkowskaMałgorzata Rutkowska
Małgorzata Rutkowska
AMAleksandra Malachowska
Aleksandra Malachowska
AAAndrzej Ambroziak
Andrzej Ambroziak
This article presents a study of corrosion resistance of tin and tin-based composite (Sn + Al2O3 and Sn + SiC) coatings deposited onto aluminium alloy substrates using the low-pressure cold spraying method. The samples were subjected to three different corrosion tests at a room temperature: (i) Kesternich test, (ii) a cyclic salt spray test and (iii) anodic polarisation test. The selected tests allowed extreme environment simulation typical for wide range of urban, industrial and marine service conditions. Evaluation of corrosion was carried out by analysing changes on the coating surface as well as in the microstructure. Additionally, the physicochemical tests were carried out using X-ray diffraction. XRD analysis clearly showed that abhurite Sn21O6Cl16(OH)14 is the main corrosion product established after the polarisation measurements. Despite extreme corrosive conditions used in experiments all tin coatings showed minor corrosion changes which implies that abhurite serves as a buffer between the metal and the oxidising natural environment.

11 September 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Aleksandra KrólickaAleksandra Królicka
Aleksandra Królicka
AAAndrzej Ambroziak
Andrzej Ambroziak
Andrzej ZakAndrzej Zak
Andrzej Zak
This article presents state-of-the-art welding methods and the weldability aspect of steels, particularly high-carbon nanobainitic (NB) steels, without carbide precipitates (CFB—carbide-free bainite). On the basis of research conducted to date, all welding methods with parameters and weld metals for NB CFB are presented. It was found that the process parameters significantly affected the mechanical properties of the welds, which were determined primarily by the properties of the low-temperature heat-affected zone. The microstructures of welded joints in the heat-affected and fusion zones are also described. The general requirements for welding processes, as well as problems and perspectives for further research, are presented.

29 October 2020 in Materials
Verified
Journal Article
Open access
PDF file
Aleksandra KrólickaAleksandra Królicka
Aleksandra Królicka
KRKrzysztof Radwański
Krzysztof Radwański
AJAleksandra Janik
Aleksandra Janik
PKPAWEŁ KUSTROŃ
PAWEŁ KUSTROŃ
AAAndrzej Ambroziak
Andrzej Ambroziak
One of the main limitations in application of nanostructured carbide-free bainite as a construction material is the difficulty of joining. This research presents a structural characterization of welded joints of medium carbon 55Si7 grade steel after the welding process with a regeneration technique as well as post welding heat treatment (PWHT). The hardness distribution of the welded joint with regeneration exhibit an overall decrease in hardness when compared to the base material and a significant decrease in hardness was observed in the heat-affected zone (HAZ). Unfavorable hardness distribution was caused by the presence of diffusion-type transformations products (pearlite) in the HAZ and bainite degradation processes. On the other hand, welding with the PWHT promotes the achievement of a comparable level of hardness and structure as in the base material. However, a slight decrease in hardness was observed in the weld zone due to the micro-segregation of the chemical composition caused by the indissoluble solidification structure. Based on the structural analysis, it was found that steel with relatively low hardenability (55Si7) should be welded using PWHT rather than a regeneration technique.

30 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
AKAnna Kus
Anna Kus
Wirginia PilarczykWirginia Pilarczyk
Wirginia Pilarczyk
AMAleksandra Malachowska
Aleksandra Malachowska
AAAndrzej Ambroziak
Andrzej Ambroziak
Piotr GębaraPiotr Gębara
Piotr Gębara
Properties of Co-based alloys with high Glass Forming Ability (GFA) in the form of powder are still not widely known. However, powders of high GFA alloys are often used for the development of bulk metallic glasses by additive manufacturing. In this work Co47.6B21.9Fe20.4Si5.1Nb5% at. and Co42B26.5Fe20Ta5.5Si5Cu1% at. were developed by gas-atomization. Obtained powders in size 50–80 µm were annealed at Tg and Tx of each alloy. Then SEM observation, EDS analyses, differential thermal analysis, X-ray diffraction, nanoindentation, Mössbauer, and magnetic properties research was carried out for as-atomized and annealed states. The gas atomization method proved to be an efficient method for manufacturing Co-based metallic glasses. The obtained powder particles were spherical and chemically homogeneous. Annealing resulted in an increase of mechanical properties such as hardness and the elastic module of Co47.6B21.9Fe20.4Si5.1Nb5% at and Co42B26.5Fe20Ta5.5Si5Cu1%, which was caused by crystallization. The magnetic study shows that Co47.6B21.9Fe20.4Si5.1Nb5 and Co42B26.5Fe20Ta5.5Si5Cu1 are soft magnetic and semi-hard magnetic materials, respectively.